Subject: 2 stroke oil in the oil pan]
From: Rotary Engine
Date: 1/26/2011, 1:40 PM
To: AAA Put this in the To box


 I am aware of the fragility of the oil lines used by Mazda from their
 oil metering pump to the point of injection, but is that a good reason
 to do away with the pump for aircraft use? I suppose if you're a belt
 and braces (suspenders) person it might be a good idea to run the pump
 and add oil to the fuel as well. I understand that some 2 stroke oils
 remain mixed better than others so surely the pump could be more
 reliable, particularly if the Antipodean habit of using 2 stroke oil in
 the sump is followed. There seems to be some strange belief out there
 that 2 stroke oils are in some way inferior to the usual heavily
 advertised engine oils that leave all sorts of deposits when burnt.

 John Evans

 That is one good reason but another is mixing spreads the oil
 better in the rotor housing. There is no doubt in my mind
 that synthetic oils, and two stroke oils are in that category, are
 better. If in doubt give it the 500 degree F oven test.
 The apex seals run 500 F at full chat.

 Paul

 Our house is regularly inspected by the neighbor's cat, his name is
 Diesel, but as I don't feed him I haven't any cat food tins. Furthermore
 my courage fails me when I contemplate the oven test you recommend:).
 I'm not sure of its relevance anyway.

 Two stroke oil is designed to burn cleanly and leave minimal deposits,
 some are better than others in this regard.
 "Crankcase" oils on the other hand are not designed to be burnt in the
 quantities required in a rotary so they do tend to leave deposits.
 Antipodean experience shows that under racing (or for that matter road)
 conditions 2 stroke oil is satisfactory in rotaries, and is apparently
 generally used.

 Of course there is the possibility that conditions are different in the
 Southern Hemisphere, perhaps it's Coriolis effect? Seriously, there
 remains the possibility that motor racing does not raise the tip seal
 temps as high as aviation use, but then dyno tuning would be similar to
 aircraft use, so why doesn't 2 stroke oil gum up the tip seals as in the
 recommended oven test?

 I know it's inconvenient to have someone asking these questions, but if
 this site is to have any resemblance to using "scientific method" we
 must be prepared to put up with this and enjoy the challenge of bouncing
 stuff off each other.
 John Evans

 -------------------------------------------------------
 It is not inconvenient to have someone asking these
 questions. We are just not in the business of
 developing oils. We are focused on making the
 rotary engine easier to install in aircraft.
 Our secondary goal is educating people on
 the advantages of the rotary.

 My test is what are we going to gain by taking a risk?
 If it is not broken don't fix it.
 It has been working for at least 30 years.
 It is a well known fact that 2 stroke oil works
 fine when mixed with the fuel to lube the apex seals.
 It is also a well know fact that 2 stroke oil burns
 cleanly. Mix half and half 2 stroke oil with
 gasoline and burn it. That will confirm that fact
 in few minutes. There are literally a thousand or
 more Mazda rotary powered cars in the US racing.
 65,000 RX8's have been sold here year after
 year until recently when everything dropped dead.

 I contacted Mazda engineering in Japan about their
 recommendation or lack there of on synthetic oil.
 This was no small achievement. It took me quite some
 time. I also got a private tour through the rotary
 engine assemble plant March 2004 in the bargain. The
 guy standing to my left was (could be still be) the
 chief engineer on the RX8.

 Mazda claimed the reason they do not recommend Mobil 1
 synthetic oil was simply because they have not tested
 it. Idemitsu has formulated a special synthetic oil
 especially for the rotary. That is now being sold
 in the US. It is what I now use instead of Mobile 1.

 I have owned at least three different rotary
 powered cars since Mobile 1 has been available
 and used it in these cars. I have owned six rotary
 powered cars total since 1973. Some with over 300,000
 US miles. I have other cars I also used it in.
 Others have also used it with no problems. I do
 know it stands up much better than all the half
 dozen mineral oils I have tested at 500 F. There
 are local hot spots in any engine under certain
 circumstances so I am thinking why take chances
 with something else?

 I had a Dodge Caravan that had 200,000 miles on
 it. Everything else failed except the engine.
 It was fed Mobil 1 its entire life. The engine was
 still running strong and passed California smog
 inspection when I got rid of it.

 The bottom line is what do you hope to gain by
 using 2 cycle oil in the crankcase? How long
 do you proposes to test it before you can conclude
 it is OK let alone better?

 Paul Lamar


 Paul,I would like to suggest a particular brand of 2-stroke oil to
 mix with gas. The motorcycle shop I worked at during college used this
 in our own bikes and sold a lot of it to customers of other brands of
 bikes. It is made by "blendzall" this is a very clean burning castor
 based oil which does not tend to settle to the bottom of the tank if the
 bike sits up for a week. We had been shaking up the bike before starting
 to remix the outboard brands of oil but didn.t need to with the
 blendzall. Some people mixed it as lean as the label recommendations
 with no problems, however I mixed it more like 22 to 1.As an added
 benefit it doesn't seem to reduce the octane of the gas prompting some
 people to claim it is an octane booster. I don't know if that is true
 but the performance seems better with it.Anyone interested in this
 product can research it on the internet.

 george grimes

 Oh dear, I can feel a philosophical ramble coming on.
 We are all, to a greater or lesser extent, products of not only our
 genes, but very much, our environment. I'm not sure where my skeptical
 streak came from, but I have to confess to being a great admirer of the
 little boy at the parade who had the temerity to point out that far from
 being dressed in his fabulous new clothes, the Emperor was wearing his
 "Birthday suit". Nobody has told us of his fate, perhaps his obvious
 mental aberration was dealt with by the popular treatment of the day.
 We can laugh at this today, but in reality our unquestioning acceptance
 of a lot of what passes for news and advertising copy today brands us as
 somewhat uncritical.

 What's this got to do with 2 stroke oil?
 My adventures with various unfortunate motorcycles (2stroke of course)
 gave me an enormous respect for what a little bit of it can do in those
 bikes despite my modifications.

 In my work as a Designated Aviation Medical Examiner, which apparently
 qualified me to also perform fitness assessments on racing drivers, I
 learned many interesting things. From multiple sources (including a
 winner at Bathurst in an RX7) I learned that certain 2 stroke oils were
 routinely used in rotaries for road and track. This has been going on
 for many years now without any adverse effects that I am aware of. This
 is not just an experiment, it is normal practice.

 Contributors to this site with long memories may recall that some time
 ago I posted the results of some tests my Engineer friend and I
 performed on various oils. In keeping with proper scientific method I
 invited attempts to confirm or debunk our findings. I was disappointed
 at the lack of any attempt to confirm or debunk.

 We undertook this research as I wanted to know whether or not the oil
 film strength of the tested 2 stroke oils was sufficient for it to be
 used in Tracey's PSRU, i.e. circulated from the oil pan. Such
 information just isn't available, all I could find was a lot of
 advertising copy and pontifical statements about the quality of various
 oils.

 Now look, I accept that the world's most popular lubricant is BULLSHIT.
 I agree that it has its place, it makes the world run smoother. Where
 would politicians be without a good supply? I don't believe we should
 use it in rotaries without further testing.
 John Evans
 Ambition: To be a good observer.


 -------------------------------------------------------------------
 -------- Original Message --------
 Subject: Oil film strength tests
 Date: Sun, 11 Jul 2010 20:31:10 -0700
 From: Rotary Engine <rotaryeng@earthlink.net
 To: AAA Put this in the To box <rotaryeng@earthlink.net


 G'Day Paul,
 I would again like to subscribe to your Newsletter.

 A few years ago I was a subscriber. At that time I posed a
 question regarding oil film strength in relation to the
 normal Australian practice of using two stroke oil in the
 sump of rotary engines, including those used in competition
 as I was proposing to use it and circulate it through one of
 Tracey Crook's reduction drives. I was unable to find any
 objective information to compare ATF and two stroke oil.

 We built a fairly simple oil film strength testing device
 giving us a reading on the load applied and the amount of
 friction generated reading as amps. On being shown our results
 recently Tracey remarked that the components of Mobil 1 were
 responsible for a lot of apex seal problems. No such problems
 appear to occur on two stroke oil here in Australia.

 If you think your subscribers would find our results of
 interest I would be happy to share them with you.

 Let me know.

 Regards

 John Evans

 Quote.

 "On being shown our results recently Tracey remarked that the
 components of Mobil 1 were responsible for a lot of apex seal
 problems."

 Whose apex seals? Tracy's apex seals? Stock Mazda apex seals?
 Tracy is selling apex seals.

 We have been running Mobil 1 for at least 25 years in our rotaries
 with stock Mazda apex seals with no problems. We did a 500 F oil
 bake test and Mobil 1 came out on top of all the oils we tested
 except for turbine oil.

 As far as I know, and some of the evidence would support that,
 Tracy's apex seals are made from steel. We warned our readers 12 years
 ago about making apex seals out of steel. Mazda apex seal history
 also indicates that. Apparently and a lot of other info supports this,
 cast iron is the best metal to make apex seals and piston rings
 for that matter. Apparently it is porous on a microscopic level
 and retains lubricant while steel does not. Mazda spent millions
 coming up with this conclusion. The 13B apex seal environment is
 severe with the seals running at over 500 F.

 Does your film strength tester test at 500F?
 Unless you are testing at 500 F you are not testing :)

 What works best is Ianetti ceramic seals made from silicon nitride.
 Silicon nitride is used in high speed ball bearings as it will
 run over 1000 F while regular ball bearings start to have
 problems at 500 F.

 Read this http://www.rotaryeng.net/seals.html


 Paul Lamar

 Thanks for your reply Paul, I don't know anything about
 Tracey's seals, I showed him the results in relation
 to his gearbox. We certainly didn't attempt to "bake " the
 oil in our tests, so far as I know what we did was a valid
 test for oil film strength in a gearbox. Both the air cooled
 and water cooled two stroke oils we tested were very good.

 Perhaps one of your subscribers would be interested in
 replicating our tests to confirm/debunk our findings?

 John Evans

 I don't think running the engine oil in the gear box is
 a good idea to begin with. You should use gear lube I suspect.
 What do the Rotax guys do? Lots of two stroke Rotax's out
 there with gear boxes.

 Paul Lamar

 _
 John, I would like to see the some reference to the testing
 protocol you are describing, for replication.
 I work at the R&E Center for Ford Motor Company in
 Dearborn MI. Having participated in numerous laboratory
 and production automotive environments, it is clear that
 he gathereing of data, and it's interpritation must be
 clearly laid out, and of course repeatable.
 I'm interested in replicating your testing protcol.
 C. Smith

 Strangely enough the person I work with is also C Smith! As I
 mentioned in the original post it was a fairly simple device we
 used consisting of a 1/4 hp electric motor with a mild steel
 disc about 1/4" wide and 1" diameter. A pivoted lever with the
 test piece mounted on it was pulled up by a large spring and
 spring balance scale to measure the load. The length of the
 lever multiplied the reading on the spring balance by a factor
 of six. The oil to be tested is applied to the test piece after
 carefully wiping off any previous oil, the load is progressively
 increased in steps and applied with the motor already running
 until oil film breakdown is evidenced by a sudden increase in
 amperage reading, the motor slowing and smoke from the oil.

 All this may seem fairly simple and even crude, but it did work
 and was impressively repeatable.

 Paul, as originally stated, the aim was to compare ATF and two
 stroke oil as Tracey's reduction drive uses the planetary set
 out of a Ford automatic - a C6 I think. As you know these are
 designed to be lubricated by ATF. We wanted to get an
 indication of their oil film strengths, but we did go on to
 check a few other oils we had on hand.

 As there seems to be some interest I'll dig the results out and
 post them shortly.



 John Evans


 John, I don't want to ruffle any feathers, but a summary look at your
 protocol only tells us relatively how long one could turn the starter
before
 damaging the bearings, if the oil pump failed immediately after 5 or
6 turns
 of the crankshaft, in a relativistic way.
 Kind of limited utility.
 C. Smith



 -------- Original Message --------
 Subject: Oil Film strength
 Date: Sun, 11 Jul 2010 03:54:43 -0700
 From: Rotary Engine <rotaryeng@earthlink.net
 To: AAA Put this in the To box <rotaryeng@earthlink.net

 Test results attached, note that XX indicates breakdown,
 the load indicated has to be multiplied by 6.
 We did the used cooking for a laugh!! Please don't
 accuse me of recommending its use as an engine
 lubricant, although it is a great diesel fuel.

 We found it necessary to do our own tests as I
 could not access any information giving an objective
 comparison. I guess some hackles will be raised by
 the relatively poor performance of Mobil 1, perhaps
 it has some other highly desirable qualities.

 John Evans

 I think we are missing something here. Probably oil
 temperature. Used cooking oil looks as good as the
 best synthetics :) Somehow I doubt that :)

 Paul Lamar


Thanks for republishing all that stuff Paul, saved me trying to find it
in my chaotic system.
I was particularly interested in George Grimes observations about the
castor oil based 2 stroke oil. I seem to recall that in the early days
of jet engine development the only thing that would withstand the temps
encountered was in fact a castor oil based lubricant. I have vivid
memories of the pungent odour of Castrol R from Speedway racing
motorcycles years ago.
I'm sure you will agree that we achieved our aim of testing the
suitability of those 2 stroke oils for use in a planetary gearbox where
the area of tooth contact is greater than with spur gears.

While it would be nice to run our tests on Idemitsu oil I don't know if
it is available here, I certainly will leave the high temp testing to
someone else, particularly as the use of 2 stroke oils in rotaries
appears to be well accepted here.

It would be great to see an attempt made to confirm/refute our findings.
While in the pool last night I had a visit from Diesel the neighbor's
cat, he agrees that I should wait for that to happen.

John Evans

Don't forget the temperature factor. You could heat your
steel test wheels to 500 F.

I don't recommend 2 stroke oil in gear boxes. Use high pressure
gear oil. It is designed for that purpose. Tracy is getting away with
high temperature crankcase oil in his gear boxes which is a testimony
for the durability of the  Ford planetary set that is used in auto
transmission. Auto TX's normally use ATF which I suspect is needed
for the friction and clutch packs found in auto tx's.

I also don't recommend it's use in the oil pan as two stroke engines
do not have plain journal bearings.  2 strokes use roller and ball
bearings. Oils are designed for specific purposes. Trust the oil
engineers. They know what they are doing.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.