Subject: Drift car
From: Rotary Engine
Date: 1/30/2011, 7:49 PM
To: AAA Put this in the To box


Hello Mr. Lamar  and rotary people :)

I´m preparing my RX 7 for drift, and I think about engine.
I´m going to use RX 7 engine with RX 8 eccentric shaft and rotors, with
p-port and turbo. Cause I need about 500 HP.
Might it be working properly? What kind of turbo and waste gate should I
use?
Respectfully,
 Dibala, Slovakia

I am not sure an RX8 shaft will work with RX7 end housings. I would check
with
Mazdatrix on that. Perhaps Cary knows. I think there is enough difference
in the shaft length. RX8 rotors will work. I think you are looking
for a p-port exhaust. It is possible to use a P-port exhaust rotor
housing in an RX8 and have three exhaust ports. That seems to work
very well. Way back in the early eighties Mazda made a 13B engine for
first gen RX7 that had the water O-rings in the rotor housing.
1984 and '85 GSL-SE: 13B engine. That P-port exhaust rotor housing
will work in the RX8 engine. That will give you 3 exhaust ports
per rotor.

It also solves a problem with highly boosted RX8 engines (over 350 HP)
that melt an iron bridge near the exhaust port. See the attached
picture. You might try modifying  the RX8 rotor housing with
an extra cooling water port and use an electric water pump to
feed cold water into this area.

It is also possible to put late 3rd gen RX7 rotor housings in an
NC mill and machine the O-rings groves for use in RX8 end housings.
That will also give you 3 exhaust ports per rotor. It also solves
the melting RX8 exhaust port problem.

Jeff Doddridge <4starr@cox.net can do that for you if he has time.

"What kind of turbo and waste gate should I use?"

I don't know what works for high power engines. Generally the largest
one you can find :) Mazdatrix might help with that as they build drift
engines.


Paul Lamar



Paul --

We have been using the RX8 shaft in our engines for MANY years -- works
fine, lighter, and less expensive.

Why would you want to take a 3rd gen housing ($798 retail) and go to all the
trouble of trying to cut the water seal grooves in it when you can buy ($475
retail) the 84-85 housings with the groove already in them???

Btw - if you put those housings in an RX8 engine you get THREE exhaust ports
per rotor -- two side and one peripheral.

Only reason to use RX8 rotors is they are a little lighter. But, the
compression is higher meaning you can not run as much boost. Also, the side
seals are more expensive -- $12.38 each for 86-95 versus $15.22 for RX8
uncut or $26.03 for pre-cut RX8's. PLUS the RX8 rotors should be cut for the
taller/stronger 86-95 [2003 in Japan] 2mm apex seals. Cost is something around $400 per rotor.

He also said he is planning on using an RX7 engine -- makes life much
easier.

We are making a reliable 475hp with the RX7 engine. Needs a lot of mods
(like oversize studding, side cutting rotors, etc.) to stay together up
there.

Dave


I thought perhaps there was a limited number of those 84-85 rotor housings
out there. Is Mazda still making and selling them? For how long? Obviously
that is 25 years ago needless to say. How time flies.

BTW a clarification on the taller/stronger 86-95 2mm apex seals just for
the new guys. That is now. Back in those years Mazda was using the largely unsuccessful three piece seals. The new replacements you mentioned are
back to  two peice. Don't use those 3 piece seals if you have them.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.