Subject: 2nd gen turbo charger cooling system.
From: Rotary Engine
Date: 3/14/2011, 8:09 AM
To: AAA Put this in the To box


 I was in the process of rebuilding the oil supply
 and turbo  water cooling system on the 2nd gen Mazda turbo charger.
 Cooling the turbo shaft has a large effect on the strength
 of the turbine blades. See the JPG. The highest stress is at
 the root of the blades attached to the shaft. If one can cool
 the shaft one can strengthen the joint.

 I had redesigned the intake manifold, made casting patterns in
 a stereo lithography machine at the local college and had castings
 made and machined. We sold out except for the one I saved for the
 turbo engine in my KIS cruiser kit. We could not use the original
 turbo intake manifold as it was too high for the low KIS cowl. In
 fact it was not a good idea to use it cut down as it gave a rather
 bad aerodynamic internal shape. Unfortunately, or fortunately
 depending on how one looks at it, we lost the turbo cooling water
 connection when we redesigned the manifold. I did not think too much
 about it until recently when it became necessary to redesign the
 cooling system.

 I was stunned to find out the cooling water going to the turbo was
already
 heated by the hottest part of the engine. That reduced the cooling
 effect on the turbo. The second stunning fact was the turbo cooling
 water drain back did not go to the flow of hot water going into the
 rad to be cooled yet again as one would think. It short circuited
 the rad and flowed back into the input side to the water pump along
 with the cool water from the rad!!!

 What the heck were the Mazda engineers thinking??? This means the
 heat put into the turbo cooling water was now heating the engine
 cooling water before it got into the engine and do its job of
 cooling the engine???? No wonder it was so hard to cool the turbo
 engine as Dave Leonard found out. He had to use a really thick rad.

 IMHO It would be much better to send the turbo cooling water to the
 rad along with the hot water from the engine. That would increase
 the temperature of the rad increasing the heat transfer to the out
 side cooling air. That would supply colder water to both the engine
 and the turbo.

 IMHO this stock turbo cooling system is partially to blame for all
 the stock turbo failures we have seen.

 What am I missing?

 This also has implications for the turbo compound version that uses
 a turbo charger.

 Paul Lamar


Paul,

There may be a couple of things involved.
1: Maybe they were thinking about after shutdown thermosyphon to cool the
turbo. The shorter distances give less resistance to the flow helping to
increase the flow rate.

2: Having the return going directly into the water pump suction line
will give
the highest differential pressure across the turbo which should help
increase
the flow through the turbo while running.

I do have to agree the heated water coming out of the engine does not
seem to
make sense. Possibly the temp of the turbo makes the inlet coolant
temp not
important. It does look like the plumbing is short in Mazda's version. A
redesign seems to be in order. For automotive use it is likely not
extremely
important but for an engine that will run for hours at 75% max power,
it is
looking mandatory.

Dale Davies

1: I guess that is a possibility but that sounds too sophisticated.

2: What do you think of sourcing  the cool water out of the outlet
side of the pump and returning to the hot side of the rad?

The water out of the block is close to steam temperature to begin
with. I think steam is coming out of the turbo, as it runs 400 F or
higher around the bearings.

Paul Lamar

Do you think that Mazda was looking at bringing the engine up to
operating temp as quickly as possible utilizing heat from the turbo?
As stated, automotive applications rarely tap sustained power for
more than several seconds.

rog

That is the best reason I have heard so far. Smog is a large issue
for car engines so that would cut emissions.

Thanks rog.

Paul Lamar/
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.