I was in the process of rebuilding the oil supply
and turbo water cooling system on the 2nd gen Mazda turbo charger.
Cooling the turbo shaft has a large effect on the strength
of the turbine blades. See the JPG. The highest stress is at
the root of the blades attached to the shaft. If one can cool
the shaft one can strengthen the joint.
I had redesigned the intake manifold, made casting patterns in
a stereo lithography machine at the local college and had castings
made and machined. We sold out except for the one I saved for the
turbo engine in my KIS cruiser kit. We could not use the original
turbo intake manifold as it was too high for the low KIS cowl. In
fact it was not a good idea to use it cut down as it gave a rather
bad aerodynamic internal shape. Unfortunately, or fortunately
depending on how one looks at it, we lost the turbo cooling water
connection when we redesigned the manifold. I did not think too much
about it until recently when it became necessary to redesign the
cooling system.
I was stunned to find out the cooling water going to the turbo was
already
heated by the hottest part of the engine. That reduced the cooling
effect on the turbo. The second stunning fact was the turbo cooling
water drain back did not go to the flow of hot water going into the
rad to be cooled yet again as one would think. It short circuited
the rad and flowed back into the input side to the water pump along
with the cool water from the rad!!!
What the heck were the Mazda engineers thinking??? This means the
heat put into the turbo cooling water was now heating the engine
cooling water before it got into the engine and do its job of
cooling the engine???? No wonder it was so hard to cool the turbo
engine as Dave Leonard found out. He had to use a really thick rad.
IMHO It would be much better to send the turbo cooling water to the
rad along with the hot water from the engine. That would increase
the temperature of the rad increasing the heat transfer to the out
side cooling air. That would supply colder water to both the engine
and the turbo.
IMHO this stock turbo cooling system is partially to blame for all
the stock turbo failures we have seen.
What am I missing?
This also has implications for the turbo compound version that uses
a turbo charger.
Paul Lamar
Paul,
There may be a couple of things involved.
1: Maybe they were thinking about after shutdown thermosyphon to
cool the
turbo. The shorter distances give less resistance to the flow
helping to
increase the flow rate.
2: Having the return going directly into the water pump suction line
will give
the highest differential pressure across the turbo which should help
increase
the flow through the turbo while running.
I do have to agree the heated water coming out of the engine does not
seem to
make sense. Possibly the temp of the turbo makes the inlet coolant
temp not
important. It does look like the plumbing is short in Mazda's
version. A
redesign seems to be in order. For automotive use it is likely not
extremely
important but for an engine that will run for hours at 75% max power,
it is
looking mandatory.
Dale Davies
1: I guess that is a possibility but that sounds too sophisticated.
2: What do you think of sourcing the cool water out of the outlet
side of the pump and returning to the hot side of the rad?
The water out of the block is close to steam temperature to begin
with. I think steam is coming out of the turbo, as it runs 400 F or
higher around the bearings.
Paul Lamar
Do you think that Mazda was looking at bringing the engine up to
operating temp as quickly as possible utilizing heat from the turbo?
As stated, automotive applications rarely tap sustained power for
more than several seconds.
rog
That is the best reason I have heard so far. Smog is a large issue
for car engines so that would cut emissions.
Thanks rog.
Paul Lamar/
Paul, I vote for the coolest turbo cooling water available. Since the
turbo housing will also be cooler there should be little difference in
thermal shock.. Using coolant that is near the steam point makes it
more likely that steam will form in the turbo reducing heat transfer.
Conversion of water to steam requires a lot of Btu (latency of heat of
evaporation) but at 30 Psi this is already hotter than the bearings need
to be running if they are roller bearings. This prompts the question,
does the heat transfer from the shaft occur from the shaft to the oil
and from the oil to the housing with the housing slowing the oil
temperature rise? That would make the housing an oil cooler also. I
would suggest that a steel line to feed the turbo oil would be better
than any kind of hose because it would lower the oil temp by radiation
which a hose would not.
george.grimes
Right on George we are putting steel pipe on both the water supply and
the oil supply as well as the corresponding drain backs.
I think these are plain bearings. Not rollers or balls.
Ceramic balls will go to 1000 C.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.