Subject: 2nd gen turbo charger cooling system.
From: Rotary Engine
Date: 3/14/2011, 8:59 PM
To: AAA Put this in the To box


I was in the process of rebuilding the oil supply
     and turbo  water cooling system on the 2nd gen Mazda turbo
  charger.   Cooling the turbo shaft has a large effect on the
  strength   of the turbine blades. See the JPG. The highest stress
is  at   the root of the blades attached to the shaft. If one can
cool  the shaft one can strengthen the joint.

I had redesigned the intake manifold, made casting patterns in
a stereo lithography machine at the local college and had castings
made and machined. We sold out except for the one I saved for the
turbo engine in my KIS cruiser kit. We could not use the original
turbo intake manifold as it was too high for the low KIS cowl. In
fact it was not a good idea to use it cut down as it gave a rather
bad aerodynamic internal shape. Unfortunately, or fortunately
depending on how one looks at it, we lost the turbo cooling water
connection when we redesigned the manifold. I did not think too much
about it until recently when it became necessary to redesign the
cooling system.
  I was stunned to find out the cooling water going to the turbo was
    already
heated by the hottest part of the engine. That reduced the cooling
effect on the turbo. The second stunning fact was the turbo
  cooling   water drain back did not go to the flow of hot water
going  into the   rad to be cooled yet again as one would think. It
short circuited the rad and flowed back into the input side to the
water pump  along   with the cool water from the rad!!!  What the
heck were the Mazda engineers thinking??? This means the heat put
into the turbo cooling water was now heating the engine cooling
water before it got into the engine and do its job of cooling the
engine???? No wonder it was so hard to cool the turbo engine as Dave
Leonard found out. He had to use a really thick rad.  IMHO It would
be much better to send the turbo cooling water to  the   rad along
with the hot water from the engine. That would increase the
temperature of the rad increasing the heat transfer to the out side
cooling air. That would supply colder water to both the  engine
 and the turbo.  IMHO this stock turbo cooling system is partially
to blame for all the stock turbo failures we have seen.  What am I missing?
  This also has implications for the turbo compound version that
  uses   a turbo charger.
  Paul Lamar
Paul,
There may be a couple of things involved.
1: Maybe they were thinking about after shutdown thermosyphon to
  cool the  turbo. The shorter distances give less resistance to the
  flow helping to  increase the flow rate.
2: Having the return going directly into the water pump suction
  line  will give  the highest differential pressure across the turbo
  which should help  increase  the flow through the turbo while running.
I do have to agree the heated water coming out of the engine does not
    seem to
    make sense. Possibly the temp of the turbo makes the inlet
coolant    temp not    important. It does look like the plumbing is
short in Mazda's  version. A  redesign seems to be in order. For
automotive use it is  likely not  extremely  important but for an
engine that will run for  hours at 75% max power,  it is  looking mandatory.
Dale Davies
1: I guess that is a possibility but that sounds too sophisticated.
2: What do you think of sourcing  the cool water out of the outlet
    side of the pump and returning to the hot side of the rad?
The water out of the block is close to steam temperature to begin
    with. I think steam is coming out of the turbo, as it runs 400 F
or    higher around the bearings. Paul Lamar

  Do you think that Mazda was looking at bringing the engine up to
  operating temp as quickly as possible utilizing heat from the
turbo?  As stated, automotive applications rarely tap sustained
power for  more than several seconds.

  rog

  That is the best reason I have heard so far. Smog is a large issue
  for car engines so that would cut emissions.

  Thanks rog.

  Paul Lamar/

Rog's notion may be part of it all right. For AC use I would
definitely pull the cool coolant from the water pump outlet and
return to the hot radiator side to try to lower the turbo temp and
get as good a flow through the turbo as possible. At that turbo temp,
 a few degrees cooler in to it may not be much help. A normal
running automotive engine ( and most industrial engines) with a
thermostat operate with a temperature differential across the
radiator of about 10 to at most 15 degrees F. I wonder how a second
cooling system just for the turbo would work. It would involve extra
weight and using a second water pump. I think you could get away
with using an electric pump just for the turbo.

Dale Davies

We are going to increase the water and oil flow as well.
Cars are only making 40 to 50 HP on average. The turbo only sees
momentary use in a car.

Paul Lamar


Hi Paul,

I was thinking as per AC use with the high duty cycle compared to automotive.
As regards to the steel lines for the oil and water, do not forget to put an S
curve or loop in for the expansion.

Dale Davies

OK Dale will do.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.