I just found out that the first RX7 turbo in 1988 had a 5 psi
waste gate opening at about 6000 RPM. It gave 185 HP.
The 1991 Turbo II model had 200 HP at 8 psi.
8 psi is only 46 inches of HG. Same engine more or less.
That is 5 HP per psi so if you want more HP leave
the waste gate closed. It would not surprised me
if this engine would generate as much as 225 HP
with the waste gate closed and a boost of around 13 psi.
That should give a much better power to weight ratio
than a C182 with about the same HP. KIS cruiser gross weight is only
2300 pounds while the C182 is 3100 pounds. Both have a payload
of 1100 pounds. That is the advantage of composite construction with
carbon fiber spar caps. However the C182 has the advantage of
a constant speed prop.
Mistral claimed 230 HP, 6200 RPM and a ceiling of 25,000 feet.
Critical altitude (where full power starts to drop off)
was 20,000 feet.
Hopefully Dave Leonard will tell us what boost
he is seeing at 6000 RPM with the waste gate opened
and closed. Dave has had his 13B turbo RV6 up to 17,000 feet.
Paul Lamar
-- I too will be very interested in what Dave L reports and, of course, what
you determine Paul.
I just rebuilt my engine this last weekend due to me bending my apex seals.
My compression dropped and I was having a terrible time starting. The engine
then started running rough at the low end when it would start. So I bit the
bullet and pulled the engine and replaced the seals (also found one broken side
seal) checked everything for damage, luckily found non (it is my understanding
that some apex seals shatter, the ones I had/have did not, but you could see
they were bent when held together back to back). In the past I would have
dickered around with everything else before I would have allowed myself to just
acknowledge the core problem (so to speak) and pull the engine and repair
internal parts. Not really a problem anymore. As I have mentioned in other
places, I am no longer afraid to "let the magic out" by cracking her open.
I started the engine yesterday and it has never started so easy or run so
smoothly (at least so far....). Of course this is my fourth time to rebuild it.
It is getting much easier ;-). The first time was really another engine that
was assembled from three cores a buddy and I got online. My ignorance and low
learning curve killed this engine with heat and bad sensors (the O-rings failed
and coolant was in the chambers). I bought new end iron and rotor chambers,
however, a the brand new Mazda center iron failed at the lower water galley. So
another build. Then, a couple of months ago, fighting hard starts and finally
finding low compression in what I thought was just the rear rotor, I just
pulled the rear rotor chamber open, replaced those seals then following it being
back together determined the front compression was low too and too far from the
psi on the newly rebuilt rear chamber. (yeah, so much for short cuts). Anyway,
the rebuild only took the weekend this time. I have all my ancillary systems in
place (and the ancillary/cooling etc seem to be working well) so it was an easy
removal and then just reinstall (ok, a bit more, but it is now methodical).
All this goes to the fact that my installation is turbo charged too. I was
only running 3lb spring when I bent the apex seals (the waste gate can be
adjustable, but currently I have a static boost with a spring...figure I should
walk before a run). I have now replaced the 3 lb spring with a 1.5 lb spring,
thus very low boost. Speculation in online commentary was that I over boosted
and/or the charge was too hot, the timing was off, the octane too low and/or the
mixture was too lean. I do not think any ONE of these is the case, however, I
will start low and increase if/when I prove it all in flight....if that ever
happens. I do have the factory intercooler, but with no airflow on the ground
it does little good.
I believe I got into a circular diagnostic mode. I would try to treat a
symptom and as I would do that I would screw something else up and eventually I
got too much timing advance, on lower octane fuel (doh, 93 is not that much more
expensive and still cheaper than Avgas) etc etc etc eventually leading to my
detonation. Of course not thinking it through I figured I would hear the
detonation like in a car...wrong, the engine, while MUCH quieter with the turbo,
is still loud AND has a prop punching the air to boot.
Anyway, as of yesterday, the engine is starting up like I have always wanted.
I am keeping the rpm's low for now (just under 4500 which is around the 22 map
that is suggested to adjust Mode 3). I hope to baby it this time until I am
secure in the process.
Yeah, it may appear that I am a complete screw up, perhaps I am, but the me of
a few years ago would sure be impressed with the me of today.
I am curious as to the "correct" PSI as to get around 200 hp without toasting
another ingine. The smaller Velocity, the SE model is rated for a I-320 (160 hp)
so everything over this is gravy.....but I want the GRAVY dang it!!!!!! :-)
(yeah, I know Paul, I should have P-porte <wink) This is an engine with a
Mistral intake and a medium street port porting by Mazdatrix), built by your
local failure mode finder.....FWIW.
Go ahead; discuss. My flame suit is all burned up...I am now pretty
impervious...well, maybe not.
Chris
Houston
Velocity SE N17010
Chris, I have bad news. They are supposed to be "bent".
It is called "crown".
The 1991 shop manual and entire web site is required reading. Same tech as the
3 rotor.
http://foxed.ca/foxed/index.php?page=rx7manual
There will be an exam. Anybody failing the exam will be suspended :)
Anybody passing the exam will receive a Phd :)
This is one way to identify most cheap after market apex seals. They are
not "bent" or no crown :) Don't use them.
http://www.rotaryeng.net/seals.html
A cracked side seal is unlikely to be noticed when the engine is running.
Some stock 3 piece seals from around 89 up would shatter if the engine
detonated at high boost. Mazda recommends retrofitting the latest stock 2 piece
seals.
Iannette ceramic seals, according to Mistral, are near impossible to shatter
despite deliberately causing the engine to detonate. Apparently the resonent
frequency is too high to cause them to shatter.
Paul Lamar
Paul,
I misspoke or perhaps mislabeled when I said I bent them. What it seems I should
have stated was I warped them. They were bent down in the middle when held
together back to back like in the illustration. Also, the springs had flattened
out.
Heck. I feel as if I have read dang near all there is to read. I have the manual
on my computer and your book in my library. Got your book when first introduced
from Spruce, I think, at full new price (yikes).
I must admit thiough that a lot of the reading "sticks" when read a second or
third time and/ or applying it to a problem or task.
Chris
Back to back is a bit ambiguous IMHO. How about top to top and bottom to
bottom? I'll have to get a set out and try them bottom to bottom. That
may be normal. Top to top the center of the top is "crowned" so a gap
at the ends is normal.
It is conceivable that in order to lower the cost of manufacture the entire
seal is purposely bent to achieving the crowning. Grinding the seal IMHO
with a crown and a high surface finish is probably very difficult to do. I do
not know of a machine that can do that easily. I could be wrong. Mazda does
not do that in house. There is a supplier that specializes in apex seals.
I also don't know whether Iannette crowns his ceramic seals. I expect
he must.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.