Subject: 10:1 or 9.7:1 rotors?
From: Rotary Engine
Date: 3/28/2011, 6:23 AM
To: AAA Put this in the To box



Paul,


I'm looking into the possibility of using the '89-'92 year  9.7:1 rotors on the P.P test engine.

Do you happen to know the redline for these rotors?

T.O. will be at 8300, but I would like the engine  redline to be 9,000 which

is less than the Renesis engine I believe.

I may have to have the 9.7:1 rotors lightened a bit.

http://www.mazdatrix.com/faq/rotorwgt.htm

I was going to go with  Renesis rotors for the 110 grams reduction

in weight and the slight increase in compression ratio, but to use

them in a 13B engine I would have to incorporate lots of the Renesis

engine parts.  E-shaft, stationary gears, counter weights etc.

The biggest issue is the durability of the stock apex seals going

over the P-ports. The Renesis rotors would have to be machined both

to accept a deeper 2mm apex seals, and fix side clearance issues

encountered when used with 13B housings.

Doug in Japan

It is the rotor bearing that is the limit. As I recall the "windowed"
version of the rotor bearing is good to 11,000 RPM with just about
all stock cast iron rotors. The RX8 rotors are just a little bit lighter.
Racing Beat uses a 3D NC mill to get a few ounces out of the stock rotors
at great expense. M V squared over R.

The 13B intake p-port, if anything, is better than 13B side input port as the
apex seals are cooled better. The worst effect on the apex seals
comes from the p-port exhaust. Not the p-port intakes. RX8 side exhaust are
easier on the apex seals. The P-port RX8 engine IMHO is the best of all worlds.

If money is no object why fool around? Go with Iannette silicon nitride
apex seals. Guaranteed to last for ever and be unbreakable.
Dave Lemon at Mazdatrix melted a steel rotor housing liner by running the engine
long after all the coolant blew out. He took the Iannette seals
out and is still running them to this day in new engines.

Paul Lamar

That is good news.  Thanks.  I believe these are what you are referring to.

http://www.racingbeat.com/RX8/Engine-Internal.html

As I understand it the Racing Beat 9.7:1 lightened rotors are even lighter than the Renesis lightened ones.
These come at a hefty price though and include a snap ring retainer for the rotor gear.  Note according to R.B. they must be used with a Renesis e-shaft.

http://www.racingbeat.com/RX7-1986-1992/Rotors/10007.html

Lighter is always better for less bearing stress but the at the rpms we run them out I think it is a  waste of funds.  Ceramic seals, I agree, would be the better investment.  Next . aluminum side housings.

What happened to your P-ported Renesis engine? For turbo compound that may be the most efficient engine to use.
Ditto the 16X, IF we will every see it.

Doug in Japan

To summarize: The car racers are looking for
as much as 350 HP normally aspirated at 11,000 RPM and 500 to 600
HP turbo charged at 11,000 RPM or more. The stock 13B 3rd gen turbo was 280
HP and the stock 2nd gen turbo was 200 HP. The stock RX8 was 250 HP normally
aspirated at 8,500 RPM.

The the p-port intake in all cases gives slightly lower fuel burn and a lot
more power at the RPM's we use. Namely 5000 to 7500 RPM. IMHO the stock engine in all cases is up to it with out structural modifications. These kinds of structural mods are not worth it nor needed for aircraft use.

IMHO anytime you make the slightest change there are unintended consequences. Other than the stock intake which does not fit the average cowl I would only enlarge the oil pan to increase oil volume. My O-470 230 HP Continental has
12 quarts for a reason. First and foremost important it delays oil heating
on take off, and second, it insures you never run out of oil on four
and five hour x countries. However the rotary does not burn oil if you mix 2 cyc
oil with the fuel.

My 250 HP at 7500 RPM p-port RX8 engine is going in Mike Will's RV4 along with a new 2.85:1 PSRU.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.