Subject: 10:1 or 9.7:1 rotors?
From: Rotary Engine
Date: 3/29/2011, 1:49 AM
To: AAA Put this in the To box


 Paul,


 I'm looking into the possibility of using the '89-'92 year  9.7:1 rotors
 on the P.P test engine.  Do you happen to know the redline for these
 rotors?

  T.O. will be at 8300, but I would like the engine  redline to be 9,000
 which is less than the Renesis engine I believe.

 I may have to have the 9.7:1 rotors lightened a bit.

 http://www.mazdatrix.com/faq/rotorwgt.htm

 I was going to go with  Renesis rotors for the 110 grams reduction in
 weight and the slight increase in compression ratio, but to use them
in a
 13B engine I would have to incorporate lots of the Renesis engine parts.
 E-shaft, stationary gears, counter weights etc.   The biggest issue
is the
 durability of the stock apex seals going over the P-ports. The Renesis
 rotors would have to be machined both to accept a deeper 2mm apex seals,
 and fix side clearance issues encountered when used with 13B housings.

 Doug in Japan

 It is the rotor bearing that is the limit. As I recall the "windowed"
 version of the rotor bearing is good to 11,000 RPM with just about
 all stock cast iron rotors. The RX8 rotors are just a little bit
lighter.
 Racing Beat uses a 3D NC mill to get a few ounces out of the stock
rotors
 at great expense. M V squared over R.

 The 13B intake p-port, if anything, is better than 13B side input
port as
 the
 apex seals are cooled better. The worst effect on the apex seals
 comes from the p-port exhaust. Not the p-port intakes. RX8 side exhaust
 are
 easier on the apex seals. The P-port RX8 engine IMHO is the best of all
 worlds.

 If money is no object why fool around? Go with Iannette silicon nitride
 apex seals. Guaranteed to last for ever and be unbreakable.
 Dave Lemon at Mazdatrix melted a steel rotor housing liner by running
the
 engine
 long after all the coolant blew out. He took the Iannette seals
 out and is still running them to this day in new engines.

 Paul Lamar

Paul,
The "window" bearings are the main bearings in the stationary gears.
For an engine that will see sustained high rpm, the high power RX8
stationary gears should be used. They incorporate many of the changes
used
for years in racing.
The rotor gear will walk out and bind the rotor between the side
housings if
used for sustained high rpm. there are a couple of methods to stop it
with
the most popular being having racing beat snap ring the gear into the
rotor.
May not be an issue on RX8 rotors (one reason to use them!)
That's my 2 cents on making them last at sustained rpm.
Can you do me a favor and see if  Dave Lemon has a scrap late model
(2010 or
2011) RX8 rotor housing he can sell me?
Thanks,
Larry

He usually has scrap housing of all types for sale at around $30.
562-426-7960


Paul Lamar


Hi Doug;
IIRC, the 89-92 stock NA redline was 8000rpm.
The RX8 high powered stationary gears are a cheap upgrade for the older
pre93 rx7 engines.
Take a look at the racing beat tech tips.
http://www.racingbeat.com/mazda/performance/rotary-tech-tips/rotors.html
In particular, look at race clearancing (beveling) the rotor tips for
the older S5 NA 9.7 rotors.
Run higher oil pressure.
Lynn and others have posted high rpm mods in places such as .  e.g.
pinning rotor bearings
www.nopistons.com
Cheers
Cary

Cary, we could not get to 8000 RPM if we tried. The prop load is always
on the engine and that limits the RPM to about 7500 max. We cannot just push
in the clutch pedal. There is no clutch. Then only for a few minutes.
The guys are cruising the motors at 4500 to 6000.

All these race modification are pretty much unnecessary at these RPMs.
You are going to scare some people.

Paul Lamar



Cary

Thanks,  After spending a day looking at postings on the RX-7 group it appears quite a lot of people have already replaced their 13B P port housings with rotors from  the 10:1 Renesis now. I know the side seal clearance is to loose to use in a P-port application and that is within my abilities to hand grind some new ones to fix.   What I'm not sure of is why some people mention the rotors are a bit wider.  Do you know where?

Doug in Japan

"replaced their 13B P port housings with rotors from  the 10:1 Renesis"

???? replace the housing with a rotor ???

Do you mean replaced their 13B P port engine's rotors with rotors from  the 10:1 Renesis?

P-port intake or exhaust?

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.