Subject: 10:1 or 9.7:1 rotors?
From: Rotary Engine
Date: 3/29/2011, 2:18 AM
To: AAA Put this in the To box


  Paul,


  I'm looking into the possibility of using the '89-'92 year  9.7:1 rotors
  on the P.P test engine.  Do you happen to know the redline for these
  rotors?

   T.O. will be at 8300, but I would like the engine  redline to be 9,000
  which is less than the Renesis engine I believe.

  I may have to have the 9.7:1 rotors lightened a bit.

  http://www.mazdatrix.com/faq/rotorwgt.htm

  I was going to go with  Renesis rotors for the 110 grams reduction in
  weight and the slight increase in compression ratio, but to use them
 in a
  13B engine I would have to incorporate lots of the Renesis engine parts.
  E-shaft, stationary gears, counter weights etc.   The biggest issue
 is the
  durability of the stock apex seals going over the P-ports. The Renesis
  rotors would have to be machined both to accept a deeper 2mm apex seals,
  and fix side clearance issues encountered when used with 13B housings.

  Doug in Japan

  It is the rotor bearing that is the limit. As I recall the "windowed"
  version of the rotor bearing is good to 11,000 RPM with just about
  all stock cast iron rotors. The RX8 rotors are just a little bit
 lighter.
  Racing Beat uses a 3D NC mill to get a few ounces out of the stock
 rotors
  at great expense. M V squared over R.

  The 13B intake p-port, if anything, is better than 13B side input
 port as
  the
  apex seals are cooled better. The worst effect on the apex seals
  comes from the p-port exhaust. Not the p-port intakes. RX8 side exhaust
  are
  easier on the apex seals. The P-port RX8 engine IMHO is the best of all
  worlds.

  If money is no object why fool around? Go with Iannette silicon nitride
  apex seals. Guaranteed to last for ever and be unbreakable.
  Dave Lemon at Mazdatrix melted a steel rotor housing liner by running
 the
  engine
  long after all the coolant blew out. He took the Iannette seals
  out and is still running them to this day in new engines.

  Paul Lamar

 Paul,
 The "window" bearings are the main bearings in the stationary gears.
 For an engine that will see sustained high rpm, the high power RX8
 stationary gears should be used. They incorporate many of the changes
 used
 for years in racing.
 The rotor gear will walk out and bind the rotor between the side
 housings if
 used for sustained high rpm. there are a couple of methods to stop it
 with
 the most popular being having racing beat snap ring the gear into the
 rotor.
 May not be an issue on RX8 rotors (one reason to use them!)
 That's my 2 cents on making them last at sustained rpm.
 Can you do me a favor and see if  Dave Lemon has a scrap late model
 (2010 or
 2011) RX8 rotor housing he can sell me?
 Thanks,
 Larry

 He usually has scrap housing of all types for sale at around $30.
 562-426-7960


 Paul Lamar


Hi Doug;
IIRC, the 89-92 stock NA redline was 8000rpm.
The RX8 high powered stationary gears are a cheap upgrade for the older
pre93 rx7 engines.
Take a look at the racing beat tech tips.
 http://www.racingbeat.com/mazda/performance/rotary-tech-tips/rotors.html
In particular, look at race clearancing (beveling) the rotor tips for
the older S5 NA 9.7 rotors.
Run higher oil pressure.
Lynn and others have posted high rpm mods in places such as .  e.g.
pinning rotor bearings
www.nopistons.com
Cheers
Cary

Cary, we could not get to 8000 RPM if we tried. The prop load is always
on the engine and that limits the RPM to about 7500 max. We cannot just push
in the clutch pedal. There is no clutch. Then only for a few minutes.
The guys are cruising the motors at 4500 to 6000.

All these race modification are pretty much unnecessary at these RPMs.
You are going to scare some people.

Paul Lamar

Hey Paul;
(you have succeeded in getting me to elaborate again ;)

I'm not trying to scare anyone.  STOCK is fine.

The Racing beat tech tips are definitely worth a read for anyone that
hasn't seen them.  Years ago you had to buy their book for this valuable
information.

Doug mentioned 8300 TO and 9000 redline.
At or above 8500rpm, Racing beat recommends reliability mods.
carbon/ceramic apex seals are recommended above 9k.

In fact, since there is no clutch (accompanied by the occasional bad
shift), sudden over rev and many other "problems" will likely cease to be
an issue...

 8300/2.85=2900rpm is in the range of current props.  The losses for a
matched (constant? speed) prop at velocity would be minimal.

Drivers habitually run cars to 9k red line.  Many racers do little more
than bevel the rotors and use carbon apex seals for 11k.
Cheers
Cary

I disagree. If you ask the people that are flying with 2.85:1 PSRU nobody
has reported over 7300 RPM. Mark Steitle has a MT or Hoffman 3 blade
constant speeds or variable pitch prop.  That is 2561 prop RPM.
Ken Welter, as far as I know, is the only other guy besides Doug that has a 3:1 PSRU and as far as I know he has never seen 7000. Even with NOS and 300 HP.

The max RPM on the CS metal prop on the 230 HP C182 is 2400 RPM.

The people that run over 3000 on the prop is the VW and O-200 F1 guys and the
diameter is about 54 inches as I recall. Prop efficiency falls off drastically as the diameter drops below 70 inches. Particularly low speed thrust as needed by a sea plane in the zero to 50 MPH range.

Here are some curves on the subject from the late great Vance Jaqua.
Rocket scientist extraordinair.


Paul Lamar



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.