Paul,
I'm looking into the possibility of using the '89-'92 year9.7:1 rotors
on the P.P test engine. Do you happen to know the redline for these rotors?
T.O. will be at 8300, but I would like the engine redline to be
9,000 which is less than the Renesis engine I believe.
I may have to have the 9.7:1 rotors lightened a bit.
http://www.mazdatrix.com/faq/rotorwgt.htm
I was going to go with Renesis rotors for the 110 grams reduction
in weight and the slight increase in compression ratio,
but to use them in a 13B engine I would have to incorporate lots
of the Renesis engine parts. E-shaft, stationary gears, counter weights
etc.The biggest issue is the durability of the stock apex seals
going over the P-ports. The Renesis rotors would have to be
machined both to accept a deeper 2mm apex seals, and fix side
clearance issues encountered when used with 13B housings.
Doug in Japan
It is the rotor bearing that is the limit. As I recall the "windowed"
version of the rotor bearing is good to 11,000 RPM with just about all
stock cast iron rotors. The RX8 rotors are just a little bit lighter.
Racing Beat uses a 3D NC mill to get a few ounces out of the stock rotors
at great expense. M V squared over R.
The 13B intake p-port, if anything, is better than 13B side input
port as the apex seals are cooled better. The worst effect on the
apex seals comes from the p-port exhaust. Not the p-port intakes.
RX8 side exhaust are easier on the apex seals. The P-port RX8
engine IMHO is the best of all worlds.
If money is no object why fool around? Go with Iannette silicon nitride
apex seals. Guaranteed to last for ever and be unbreakable.
Dave Lemon at Mazdatrix melted a steel rotor housing liner by
running the engine long after all the coolant blew out. He took
the Iannette seals out and is still running them to this day in new engines.
Paul Lamar
Paul,
The "window" bearings are the main bearings in the stationary gears.
For an engine that will see sustained high rpm, the high power RX8
stationary gears should be used. They incorporate many of the changes
used for years in racing. The rotor gear will walk out and
bind the rotor between the side housings if used for sustained high
rpm. there are a couple of methods to stop it with the most popular
being having racing beat snap ring the gear into the rotor. May not
be an issue on RX8 rotors (one reason to use them!) That's my 2
cents on making them last at sustained rpm. Can you do me a favor
and see if Dave Lemon has a scrap late model (2010 or 2011) RX8
rotor housing he can sell me? Thanks, Larry
He usually has scrap housing of all types for sale at around $30.
562-426-7960
Paul Lamar
Larry, I had a '73 RX3 with the 12A engine. Ran it all the time at 9000 RPM
racing Mustangs and Camaros with 350 cube engines. The car was less than
2100#. Being young and excitable I banged it into 2nd gear downshifting at
too high a speed and spun the engine up to about 11,000RPM. The rear rotor
gear walked out a bit and it started to burn oil. I got a friend to help
pull the engine with achain and 2 by 4. I tapped the rotor gear back in
place and sanded the housing a bit on 3/4" glass with emery cloth and then
crocus cloth "glued" down with grease. I did not even buy seals or gaskets.
No problem and made a mental note, no more +9000 RPM. Doug, Which PSRU are
you using and what size prop? That RPM seems high unless you are using a
smaller diameter. As stated above, I believe the engine will have no
problem with the RPM you propose. What is the cost of Renesis rotors? The
RB lightened rotors are kind of pricey, but 2 pounds off the weight. Dale
Davies
Dale Modified Bell 47. 3:1 ratio. Prop MT, electric C/S. 76" dia.
three blade composite . My friends with the identical prop and airplanes
but powered by Lycoming IO-540s, consistently take-off with rpms of 2700 or
above. One person claims 2800 rpm. MT claims they are good to 3,000 rpms
but I'd imagine they would be less efficient at that speed.Key point in the
discussion is the PSRU ratio and prop type. As Paul correctly stated he
couldn't get the engine to reach 8,000 even without a clutch?? And he won't
unless he uses a different ratio PSRU and prop. With a 3:1 ratio the rotor
is spinning the same speed as the prop. 2,733 rotor speed is an e-shaft
speed of 8,200. The engine is just starting to wake-up and IMHO showing off
its potential for a good aircraft engine.
Personally I'd rather see PSRU
ratios in the 3.1:1 or 3.2:1 range. I agree with Paul that to manage heat
load and engine life, cruise should be around 6,000 rpm. Mazdatrix has the
Renesis rotors for sale at $651. I don't know how much they would charge
for milling the apex slots out deeper to accept a standard 2mm wide apex
seal though. Perhaps you can ask.Lighter is always better on any rotating
mass but the Renesis rotors are pretty optimized 'as is'Reduction of 0.2 lbs
not 2 lbs is possible.
Regards Doug in Japan
Mazda now has a set of 2 pcs seals that are not as deep for retrofitting
early engines.
Tracy current psru is 2.85:1 2700 RPM gives 7695.
Doug's transmission is irreplaceable for all practical purposes
and that includes all the parts. If you asks the helicopter guys you
get quotes of $30,000 for a Bell 47 final drive.
Most people use a 3 rotor for a big heavy Seawind. Doug is worried
that he won't get enough power with a two rotor to get up and off the water.
Paul Lamar
Hi Doug,
RB claims rotor weight of 9.7# and reduced to 8.7# after machining. Times two
rotors.
I am looking into the Dodge 68RFE transmission. First gear is 3.23:1. Built
for use behind the Cummins with 800lb/ft of torque. Should be good for higher
HP engines.
Dale Davies
Hey guys don't use HTML when sending messages. It creates a mess on this end
when forwarded. Just turn it off in your email program. I spend a lot of time
cleaning up the mess.
HTML was invented for fancy documents and advertising. A word is a word.
Don't use it here.
Dale, take a look at the Allison. Widely used in Chevy trucks.
This outfit has free parts break downs for all transmissions.
http://www.makcotransmissionparts.com/Allison-1000.html
Neither look as easy to use as the C6/A4OD.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.