Paul,
I'm looking into the possibility of using the '89-'92 year9.7:1 rotors
on the P.P test engine. Do you happen to know the redline for these rotors?
T.O. will be at 8300, but I would like the engine redline to be
9,000 which is less than the Renesis engine I believe.
I may have to have the 9.7:1 rotors lightened a bit.
http://www.mazdatrix.com/faq/rotorwgt.htm
I was going to go with Renesis rotors for the 110 grams reduction
in weight and the slight increase in compression ratio,
but to use them in a 13B engine I would have to incorporate lots
of the Renesis engine parts. E-shaft, stationary gears, counter weights
etc.The biggest issue is the durability of the stock apex seals
going over the P-ports. The Renesis rotors would have to be
machined both to accept a deeper 2mm apex seals, and fix side
clearance issues encountered when used with 13B housings.
Doug in Japan
It is the rotor bearing that is the limit. As I recall the "windowed"
version of the rotor bearing is good to 11,000 RPM with just about
all stock cast iron rotors. The RX8 rotors are just a little bit lighter.
Racing Beat uses a 3D NC mill to get a few ounces out of the stock rotors
at great expense. M V squared over R.
The 13B intake p-port, if anything, is better than 13B side input
port as the apex seals are cooled better. The worst effect on the
apex seals comes from the p-port exhaust. Not the p-port intakes.
RX8 side exhaust are easier on the apex seals. The P-port RX8
engine IMHO is the best of all worlds.
If money is no object why fool around? Go with Iannette silicon nitride
apex seals. Guaranteed to last for ever and be unbreakable.
Dave Lemon at Mazdatrix melted a steel rotor housing liner by
running the engine long after all the coolant blew out. He took
the Iannette seals out and is still running them to this day in new engines.
Paul Lamar
Paul,
The "window" bearings are the main bearings in the stationary gears.
For an engine that will see sustained high rpm, the high power RX8
stationary gears should be used. They incorporate many of the changes
used for years in racing. The rotor gear will walk out and
bind the rotor between the side housings if used for sustained high
rpm. there are a couple of methods to stop it with the most popular
being having racing beat snap ring the gear into the rotor. May not
be an issue on RX8 rotors (one reason to use them!) That's my 2
cents on making them last at sustained rpm. Can you do me a favor
and see if Dave Lemon has a scrap late model (2010 or 2011) RX8
rotor housing he can sell me? Thanks, Larry
He usually has scrap housing of all types for sale at around $30.
562-426-7960
Paul Lamar
Larry, I had a '73 RX3 with the 12A engine. Ran it all the time at
9000 RPM racing Mustangs and Camaros with 350 cube engines. The car
was less than 2100#. Being young and excitable I banged it into 2nd
gear downshifting at too high a speed and spun the engine up to
about 11,000RPM. The rear rotor gear walked out a bit and it
started to burn oil. I got a friend to help pull the engine with
achain and 2 by 4. I tapped the rotor gear back in place and sanded
the housing a bit on 3/4" glass with emery cloth and then crocus
cloth "glued" down with grease. I did not even buy seals or
gaskets. No problem and made a mental note, no more +9000 RPM. Doug,
Which PSRU are you using and what size prop? That RPM seems high
unless you are using a smaller diameter. As stated above, I believe
the engine will have no problem with the RPM you propose. What is
the cost of Renesis rotors? The RB lightened rotors are kind of
pricey, but 2 pounds off the weight. Dale Davies
Dale Modified Bell 47. 3:1 ratio. Prop MT, electric C/S. 76" dia.
three blade composite . My friends with the identical prop and airplanes
but powered by Lycoming IO-540s, consistently take-off with rpms of
2700 or above. One person claims 2800 rpm. MT claims they are good
to 3,000 rpms but I'd imagine they would be less efficient at that
speed.Key point in the discussion is the PSRU ratio and prop type.
As Paul correctly stated he couldn't get the engine to reach 8,000
even without a clutch?? And he won't unless he uses a different
ratio PSRU and prop. With a 3:1 ratio the rotor is spinning the
same speed as the prop. 2,733 rotor speed is an e-shaft speed of 8,
200. The engine is just starting to wake-up and IMHO showing off
its potential for a good aircraft engine.
Personally I'd rather see PSRU
ratios in the 3.1:1 or 3.2:1 range. I agree with Paul that to
manage heat load and engine life, cruise should be around 6,000 rpm.
Mazdatrix has the Renesis rotors for sale at $651. I don't know
how much they would charge for milling the apex slots out deeper to
accept a standard 2mm wide apex seal though. Perhaps you can
ask.Lighter is always better on any rotating mass but the Renesis
rotors are pretty optimized 'as is'Reduction of 0.2 lbs not 2 lbs is
possible.
Regards Doug in Japan
Mazda now has a set of 2 pcs seals that are not as deep for retrofitting
early engines.
Tracy current psru is 2.85:1 2700 RPM gives 7695.
Doug's transmission is irreplaceable for all practical purposes
and that includes all the parts. If you asks the helicopter guys
you get quotes of $30,000 for a Bell 47 final drive. Most people
use a 3 rotor for a big heavy Seawind. Doug is worried that he
won't get enough power with a two rotor to get up and off the water.
Paul Lamar
Hi Doug,
RB claims rotor weight of 9.7# and reduced to 8.7# after machining.
Times two rotors. I am looking into the Dodge 68RFE transmission.
First gear is 3.23:1. Built for use behind the Cummins with 800lb/ft
of torque. Should be good for higher HP engines.
Dale Davies
Hey guys don't use HTML when sending messages. It creates a mess on
this end when forwarded. Just turn it off in your email program. I
spend a lot of time cleaning up the mess.
HTML was invented for fancy documents and advertising. A word is a word.
Don't use it here.
Dale, take a look at the Allison. Widely used in Chevy trucks.
This outfit has free parts break downs for all transmissions.
http://www.makcotransmissionparts.com/Allison-1000.html
Neither look as easy to use as the C6/A4OD.
Paul Lamar
Hi Paul,
Does mine come through in HTML?
My reasons to look at the Chrysler 68RFE transmission parts are:
1: more gear ratio like Doug mentioned.
2: high power capability for 3+ rotors with power recovery and turbo charge
intake for turbo normalize.
3: working at a Chrysler dealer now.
They do not list the 68RFE.
In my heavy duty wrenching days, I got the opportunity to get training on
Allison transmissions; AT 540 series, AT740/750 series and the 5800 and 5900.
The 5800/5900 transmissions are used in off-highway construction and mining
equipment behind 600 to 700HP 12V engines.
Dale Davies
I think yours is plain text.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.