Paul, I'm looking into the possibility of using the '89-'92 year 9.7:1
rotors on the P.P test engine. Do you happen to know the redline for these
rotors? T.O. will be at 8300, but I would like the engine redline to be
9,000 which is less than the Renesis engine I believe. I may have to have
the 9.7:1 rotors lightened a bit.
http://www.mazdatrix.com/faq/rotorwgt.htm
I was going to go with Renesis rotors for the 110 grams reduction in weight
and the slight increase in compression ratio, but to use them in a 13B
engine I would have to incorporate lots of the Renesis engine parts.
E-shaft, stationary gears, counter weights etc. The biggest issue is the
durability of the stock apex seals going over the P-ports. The Renesis
rotors would have to be machined both to accept a deeper 2mm apex seals, and
fix side clearance issues encountered when used with 13B housings.
Doug in
Japan
It is the rotor bearing that is the limit. As I recall the "windowed"
version of the rotor bearing is good to 11,000 RPM with just about all stock
cast iron rotors. The RX8 rotors are just a little bit lighter. Racing
Beat uses a 3D NC mill to get a few ounces out of the stock rotors at great
expense. M V squared over R. The 13B intake p-port, if anything, is better
than 13B side input port as the apex seals are cooled better. The worst
effect on the apex seals comes from the p-port exhaust. Not the p-port
intakes. RX8 side exhaust are easier on the apex seals. The P-port RX8
engine IMHO is the best of all worlds. If money is no object why fool
around? Go with Iannette silicon nitride apex seals. Guaranteed to last
for ever and be unbreakable. Dave Lemon at Mazdatrix melted a steel rotor
housing liner by running the engine long after all the coolant blew out. He
took the Iannette seals out and is still running them to this day in new
engines.
Paul Lamar
Paul, The "window" bearings are the main bearings in the stationary
gears. For an engine that will see sustained high rpm, the high power RX8
stationary gears should be used. They incorporate many of the changes used
for years in racing. The rotor gear will walk out and bind the rotor
between the side housings if used for sustained high rpm. there are a
couple of methods to stop it with the most popular being having racing beat
snap ring the gear into the rotor. May not be an issue on RX8 rotors (one
reason to use them!) That's my 2 cents on making them last at sustained rpm.
Can you do me a favor and see if Dave Lemon has a scrap late model (2010 or
2011) RX8 rotor housing he can sell me? Thanks, Larry
He usually has scrap housing of all types for sale at around $30.
562-426-7960 Paul Lamar Hi Doug; IIRC, the 89-92 stock NA redline was
8000rpm. The RX8 high powered stationary gears are a cheap upgrade for the
older pre93 rx7 engines. Take a look at the racing beat tech tips.
http://www.racingbeat.com/mazda/performance/rotary-tech-tips/rotors.html In
particular, look at race clearancing (beveling) the rotor tips for the older
S5 NA 9.7 rotors. Run higher oil pressure. Lynn and others have posted
high rpm mods in places such as . e.g. pinning rotor bearings
www.nopistons.com Cheers Cary
Cary, we could not get to 8000 RPM if we tried. The prop load is always
on the engine and that limits the RPM to about 7500 max. We cannot just
push in the clutch pedal. There is no clutch. Then only for a few minutes.
The guys are cruising the motors at 4500 to 6000. All these race
modification are pretty much unnecessary at these RPMs. You are going to
scare some people.
Paul Lamar
Hey Paul; (you have succeeded in getting me
to elaborate again ;) I'm not trying to scare anyone. STOCK is fine. The
Racing beat tech tips are definitely worth a read for anyone that hasn't
seen them. Years ago you had to buy their book for this valuable
information. Doug mentioned 8300 TO and 9000 redline. At or above 8500rpm,
Racing beat recommends reliability mods. carbon/ceramic apex seals are
recommended above 9k. In fact, since there is no clutch (accompanied by the
occasional bad shift), sudden over rev and many other "problems" will likely
cease to be an issue... 8300/2.85=2900rpm is in the range of current props.
The losses for a matched (constant? speed) prop at velocity would be
minimal.
Drivers habitually run cars to 9k red line. Many racers do little
more than bevel the rotors and use carbon apex seals for 11k. Cheers Cary I
disagree. If you ask the people that are flying with 2.85:1 PSRU nobody has
reported over 7300 RPM. Mark Steitle has a MT or Hoffman 3 blade constant
speeds or variable pitch prop. That is 2561 prop RPM. Ken Welter, as far
as I know, is the only other guy besides Doug that Has a 3:1 PSRU and as far
as I know he has never seen 7000. Even with NOS and 300 HP. The max RPM on
the CS metal prop on the 230 HP C182 is 2400 RPM. The people that run over
3000 on the prop is the VW and O-200 F1 guys and the diameter is about 54
inches as I recall. Prop efficiency falls off drastically as the diameter
drops below 70 inches. Particularly low speed thrust as needed by a sea
plane in the zero to 50 MPH range. Here are some curves on the subject from
the late great Vance Jaqua. Rocket scientist extraordinair.
Paul Lamar
Paul,
How about this explanation. Gearbox inefficiencies:
Work load limits engine rpm. Work is the energy absorbed by
turning the prop, gearbox and attached engine accessories.
I propose a mind exercise:
Imagine two engines on identical airplanes with identical
C/S props. Both have the pitch set flat and are
spinning at 2700 rpms. Both props shafts are seeing
290Hp. of power. One engine is an Lycoming
IO-540 and the other is a rotary. If you like, imagine
both identical airplanes are amphibians and that it
has been proven both take off just fine at these power
settings. The rotary could be an 'enhanced' 13B or 20B.
Either one is within the realm of technical reality. .
Selecting which engine to use in an airplane is an exercise
in optimizing the power to weight ratio. That often means
operating the engine near it's peak efficiency point for the
five minutes during the T.O. and climb event. Unlike the
Lycoming however the rotary will have to produce over 300
hp, Here's why.
The rotary engine is turning the prop through a
gearbox. This gearbox reduces the e-shaft engine rpm
and increases the torque the propeller shaft sees in direct
relationship to its' gear set ratio. It also reduces power
to the prop by incurring friction loses. Said another way
the gear box acts like a drag lowering engine rpm and hence
some power output is absorbed by the gearbox and turns to
heat. Some gear box designs are more efficient then
others. The number of gears, contact area, gear profile and
cut, line speed, oiling method, planetary bearing type
and windage all affect the gearbox losses. No
gearbox is almighty but some designs are less draggy than
others without compromising reliability. A robust planetary
cluster able to handle huge torque loads does not necessary
mean it is designed to handle high speeds without incurring
huge losses.
For planetary gear boxes, a 2% efficiency loss per
step down stage is consider state-of-the-art in large
megawatt wind turbine applications. These are megabuck
designs resulting from megabuck R&D programs. The
transmissions are usually two stages and input and output a
maximum of 60 and 1800 rpms respectively. That's a 6:1
ratio followed by a 5:1 ratio.
For Tracy's 2:85:1 gearbox, I'd guess the
efficiency is in the neighborhood of 95% +/- 1%.
Anyone monitoring gear box temperatures?
In our above example this loss of power through friction is
going to cost the rotary engine rpms and hence power.
How much prop power loss depends on the power curve shape
and where on the curve the gearbox is set-up to operate.
In conclusion for any engine with PSRU attached, it is
going to have to produce more power to overcome gearbox
parasitic losses.
Prop pitch and prop efficiencies are other variables
affecting engine rpm. Those effects are multiplied by
gearbox inefficiencies.
Doug in Japan
5% of 250 HP is 1.25 HP. At 745 watts per HP that would be
almost
1000 watts. I doubt seriously Tracy's gear box is
generating 1000
watts of heat.
Here is a P&W planetary that is over 99.5% efficient
from 60% to 100% power.
Doug, please try limiting the line length to 75
characters.
I am trying to figure out what is going on.
Paul Lamar
That's 12.5 HP.
dan
Right Dan. Sorry. Thanks for catching that error. Even more unlikly
at 9,300 watts. You could heat an entire house :)
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.