Subject: Combustion/ Mixture Pattern? Rotor-housing too hot?
From: Rotary Engine
Date: 3/29/2011, 9:31 PM
To: AAA Put this in the To box



  The attached picture is from my single rotor PP engine after about 10
  hrs running time. Most of the time was running at WOT and 6000RPM. fuel
  flow was around 8gph.
  If this an indicator of mixture distribution at ignition, what does it
  mean? if anything. Has that been observed by anyone else?

  Richard Sohn
  N2071U

  You got me. I have never seen anything like that.
  What kind of oil are you mixing?

  Paul Lamar

I am using 1.25oz/gal ECHO two stroke oil.

Richard Sohn   N2071U


It looks to me like there is silicone partly blocking the coolant passage to
the left of the leading plug. There is a difference in the marking of the
housing to the left of the plug. Almost as if there is damage to the apex
seals as they cross the leading plug. Also of note is the burn mark before the
trailing plug. Could this be blow by past damage to the apex seals? There is
also a curious line across the housing just before the trailing plug. It also
looks like the apex seals were not following the rotor housing after the minor
axis indicated by the burn discoloration. How is the coolant flow with the new
end housings? I would put a thermocouple in as per Paul's description to
monitor the metal temp on further runs.

Dale Davies

Good call Dale. Richard is building his own end housings so that area
may not be getting as much water as it needs. Could also be your water pump
is not up to it Richard. As I recall the 2 rotor needs about 30 gallons
per minute.

Here is the picture from my book How to Cool Your Wankel.
"installing a "cylinder head temperature" gage. This can be done by
drilling a small hole in the rotor housing in the place shown and
installing a thermal couple."

BTW Mario called me from Germany this morning and took me to task
for the careless use of the word "Wankel" since he now owns the copyrights.

It is like copy and Zerox.

Paul Lamar

Richard,

Could the spark plug be kinda bottoming in the threads and distorting the
rotor housing? It is polished right at the sides of the plug hole, but burnt
farther out.

Dale Davies


-- 
 Hi Richard;
 The centerline smudge running left from both plugs is a sign of heat.
 Were the smudges there previously?
 It might be blow by, grooved surface, apex clearance?
 Have you checked the rotor housing surface and apex seals with a ruler
 and back lighting for flatness?

 Those orings also appear to be too large.

 Cheers
 Cary

 Richard,

 Attached is a picture of a rotor housing that was severely overheated.
  It has a similar pattern that you're seeing.  I think the residue is
 from burnt coolant.  From the looks of the TES o-ring, it appears the
 teflon got very hot, possibly compromising the seal.  Has the engine
 been overheated?  What EGT do you see at WOT?

 Mark S.


Thanks for all the excellent responses.
After doing some more checking on all the parts and indicators, it appears
to me now that high temperature in the plug area is the most likely culprit.
The EGT at my test runs was pretty constant 1600 to 1650F , and coolant
temperature never went above 180F. One thing could have caused a local
overheat is the fact that I run all these tests at a atmospheric coolant
pressure. There was leak I could not find, so I started with the testing
anyway. However, when I disassembled the engine, there was a damaged stud
o-ring, which very likely was the reason for the leak.  --

Richard Sohn
N2071U


I would still install the thermocouple near the lower spark plug.
You may have local film boiling in that area which is allowing the
metal to go higher than 500 F coking the apex seal oil. You cannot
always rely on the pressure in the cooling system to reduce the local
film boiling.

I would also measure the coolant flow through the block with a flow
meter set up just to be sure you are getting enough water flow. I'll loan
you my flow meter set up  if you send me your shipping address.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.