Subject: Combustion/ Mixture Pattern? Rotor-housing too hot?
From: Rotary Engine
Date: 3/30/2011, 6:37 AM
To: AAA Put this in the To box



The attached picture is from my single rotor PP engine after about 10
hrs running time. Most of the time was running at WOT and 6000RPM. fuel
flow was around 8gph.
If this an indicator of mixture distribution at ignition, what does it
mean? if anything. Has that been observed by anyone else?

Richard Sohn
N2071U

You got me. I have never seen anything like that.
What kind of oil are you mixing?

Paul Lamar

 I am using 1.25oz/gal ECHO two stroke oil.

 Richard Sohn N2071U


 It looks to me like there is silicone partly blocking the coolant
 passage to
 the left of the leading plug. There is a difference in the marking
 of the
 housing to the left of the plug. Almost as if there is damage to the
 apex
 seals as they cross the leading plug. Also of note is the burn mark
 before the
 trailing plug. Could this be blow by past damage to the apex seals?
 There is
 also a curious line across the housing just before the trailing
 plug. It also
 looks like the apex seals were not following the rotor housing after
 the minor
 axis indicated by the burn discoloration. How is the coolant flow
 with the new
 end housings? I would put a thermocouple in as per Paul's description to
 monitor the metal temp on further runs.

 Dale Davies

 Good call Dale. Richard is building his own end housings so that area
 may not be getting as much water as it needs. Could also be your
 water pump
 is not up to it Richard. As I recall the 2 rotor needs about 30 gallons
 per minute.

 Here is the picture from my book How to Cool Your Wankel.
 "installing a "cylinder head temperature" gage. This can be done by
 drilling a small hole in the rotor housing in the place shown and
 installing a thermal couple."

 BTW Mario called me from Germany this morning and took me to task
 for the careless use of the word "Wankel" since he now owns the
 copyrights.

 It is like copy and Zerox.

 Paul Lamar

 Richard,

 Could the spark plug be kinda bottoming in the threads and
 distorting the
 rotor housing? It is polished right at the sides of the plug hole,
 but burnt
 farther out.

 Dale Davies


 --  Hi Richard;
The centerline smudge running left from both plugs is a sign of heat.
Were the smudges there previously?
It might be blow by, grooved surface, apex clearance?
Have you checked the rotor housing surface and apex seals with a ruler
and back lighting for flatness?

Those orings also appear to be too large.

Cheers
Cary

Richard,

Attached is a picture of a rotor housing that was severely overheated.
It has a similar pattern that you're seeing.  I think the residue is
from burnt coolant.  From the looks of the TES o-ring, it appears the
teflon got very hot, possibly compromising the seal.  Has the engine
been overheated?  What EGT do you see at WOT?

Mark S.


 Thanks for all the excellent responses.
 After doing some more checking on all the parts and indicators, it
 appears
 to me now that high temperature in the plug area is the most likely
 culprit.
 The EGT at my test runs was pretty constant 1600 to 1650F , and coolant
 temperature never went above 180F. One thing could have caused a local
 overheat is the fact that I run all these tests at a atmospheric coolant
 pressure. There was leak I could not find, so I started with the testing
 anyway. However, when I disassembled the engine, there was a damaged
 stud
 o-ring, which very likely was the reason for the leak.  --

 Richard Sohn
 N2071U


 I would still install the thermocouple near the lower spark plug.
 You may have local film boiling in that area which is allowing the
 metal to go higher than 500 F coking the apex seal oil. You cannot
 always rely on the pressure in the cooling system to reduce the local
 film boiling.

 I would also measure the coolant flow through the block with a flow
 meter set up just to be sure you are getting enough water flow. I'll
 loan  you my flow meter set up  if you send me your shipping address.

 Paul Lamar



Richard,

The TES o-ring shows signs of high temps in the plug area.  The outer
teflon jacket is melted, indicating very high temps.  This is the area
of highest temps.  I think you have cooling issues going on here.  As
Paul suggested, it would help to have a CHT probe next to the leading
plug to measure your temps in this area.  As they say, "one test is
worth a hundred theories."

Mark S.

Also I might add the heat treat on the aluminum rotor housing starts to
go away at 500 F.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.