<http://www.ret-monitor.com/articles/>
BEARINGS
The turbocharger bearing - a unique challenge?
Making a comeback from earlier times, the ball-race bearing system may
be a preferred solution in some turbocharger applications, but for
reasons of cost the more usual approach for the vast majority of units
is still the fully floating design. Consisting essentially of two
bushes, one at either end of the bearing housing through which the shaft
passes, unusually these bushes themselves are allowed to rotate in their
housing, creating in effect a 'bearing within a bearing'...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=bearings&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=bearings&date_n=201105>
CAMSHAFTS
Three into two will go
High lifts or long durations are common features in high-performance
camshafts, and when optimised can produce high engine torques over a
useful but often limited range of engine speeds. The introduction of
variable valve timing can widen this range of useful speeds, but at part
load against a partially closed throttle, large valve lifts introduce
pumping inefficiencies that are increasingly unacceptable in performance
roadcar engines. Over the past decade, therefore, a multitude of
variable valve lift concepts for spark-ignition engines have evolved.
The simplest of these is the...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=camshafts&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=camshafts&date_n=201105>
COATINGS
Piston skirt coatings
The contribution of the piston assembly to overall engine frictional
losses is well documented and has been the subject of a lot of research
over a number of decades. In SAE paper 911230, for example, the authors
Tsuchida and Tsuzuku study the effects of various design features on
piston friction losses for high-speed engines (up to 16,000 rpm). At the
time - the late 1980s and early '90s - the Japanese were selling
production motorcycles with engine speeds higher than even Formula One
engines...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=coatings&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=coatings&date_n=201105>
ECU-EMS
Turbocharging the ECU
With a number of new race formulae moving over to pressure-charged
engines, the second decade of the 21st century looks set to become the
Second Coming of the turbocharger. The First Coming, of course - if my
memory serves me correctly, back in the late 1970s/early '80s - was all
about boost levels and ultimate power. This time around, with virtually
all vehicle OEMs looking at downsizing and turbocharging their street
offerings, it's about efficiency. And, as such it, will be more
important than ever to get the engine...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=ecu-ems&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=ecu-ems&date_n=201105>
RINGS
Sealing the Wankel engine
If you think sealing the gap between the piston and cylinder bore of a
conventional reciprocating engine presents something of a challenge,
then spare a thought for the problems facing the Wankel engine. Once
heralded as the rightful successor to the humble piston engine, the
rotary Wankel unit gave a smoother power delivery in a more compact
form, but early examples suffered greatly from combustion gas sealing
issues between the rotor and its housing. And if you examine the
dynamics of it all, you begin to see why...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=rings&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=rings&date_n=201105>
SURFACE-TREATMENTS
Superfinishing
There are often lots of shiny parts in a race engine, and some companies
produce parts of a high surface finish as a sales point; there is a
perception by some that a polished part is better quality and therefore
has an inherently higher value. There are very good reasons though why
some parts benefit from having a high level of surface finish. One only
has to look at the data presented in engineering textbooks on the
subject of fatigue strength and cyclic...
Read More...
<http://newsletter.ret-monitor.com/adserver/out3.php?keyword=surface-treatments&date_e=20110512>
------------------------------------------------------------------------
<http://newsletter.ret-monitor.com/adserver/out_n.php?keyword=surface-treatments&date_n=201105>
<http://www.highpowermedia.com/>
Randolph Toom
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.