Subject: Rebuild parts list [was Re: Assembly Manual
From: Rotary Engine
Date: 5/25/2011, 4:04 AM
To: AAA Put this in the To box


  I should be getting my o-rings in any day now so I can put my engine
  back together.  Is there a manual that will tell me how to reassemble?
  I will need bolt torques, and how to put the rotor in the housing
  without all the seals and springs falling out.  Are the seals just held
  in place with some grease or is there some special assembly procedure?
  Thanks,
  Randy

  http://www.rotaryeng.net/interesting.html

  http://foxed.ca/foxed/index.php?page=rx7manual


  Use a bit a Vaseline to hold the O-rings in place.

  As Tracy points
  out don't use RTV to hold the rings in place as it could harden
  and add to your problems. Buy the O-rings slightly under size on the big
  diameter (no more than 5% under size) and stretch slightly them on a
  plywood form for a few days before installing them. They will then lie
  in the slot perfectly as we discovered with Perry's installation.
  Don't try to stretch the ring by hand or by another method as you
  could permanently neck them down.

  http://www.rotaryeng.net/seals.html
  http://www.rotaryeng.net/O-ring-size2.html

  Paul Lamar

 Cold Vaseline out of the freezer works well.
 Hylomar works - use thin applications.  Avoid the new universal blue
 formulation, it hardens quickly and is lower temp -
 I *think* the new advanced formulation is equivalent to the old
 non-setting hylomar.

 Slightly undersize TESorings can be easily expanded by heat for fitting
 if necessary.
 Undersize orings can be stretched with light finger pressure without
 necking down.
 Better yet order the correct size - no stretching required
 At last measurement, new TES orings from RWS/Tracy measured .100" new,
 and a set of used (compressed) orings measured .012-.015 wider than
 (compressed) .093 from Creavey
 (probably outside the creavey nominal crush spec - I would have to check
 again)
  http://www.creavey.com/materials.html

 Personally I would just buy stock orings now, given all the trouble
 people have had.
  http://www.rx7club.com/showthread.php?t=626610

 "Creavey sells custom viton, FEP teflon, PFA teflon (500F) orings.
 You could order lengths to a thousandth of an inch. Wide variety of
 thicknesses.
 Approximately correct oring sizes were on file for 13B engines at
 Creavey. Ask!
 No crap STRETCHING REQUIRED!!!
 Several different correct oring lengths were published by different
 folks.
 Slightly different lengths were required for the different (casting)
 generations of housings.

 RA and McMasterCarr selections were larger diameter, likely leading to
 hydro lock and opening up a gap to exhaust gas exposure, lost coolant
 and ultimately leading to oring failure.
 Creavey specified a nominal crush. RA and McMaster seals were too big by
 that spec.
 I have seen several engines with failed orings as a result, although
 many have also been fine.

 They were way cheaper than OEM and properly selected they fit and are
 reusable...
 Or ignore all this and search for Lynn H's uber cheapest oring
 replacements..."

 Cheers
 Cary

 Over size O-rings can lead to cracked end housings.
 Buy Creavey only and mic them to be sure they are less
 than .093. I have seen the McMaster version and they are junk.
 I don't know where Tracy's is getting his.

 The slight stretch is to keep them on the plywood until
 they take a set that will keep them in the groove when assembling
 the engine. They come coiled up for packaging reasons. You will encounter
 that when you get them.

 http://www.rotaryeng.net/O-ring-size2.html

 Lynn Hannover used Teflon coated  hook up wire:) Not recommended for
 aircraft.

 You have to buy a whole overhaul kit to get new Mazda O-rings.
 They are not sold separately.

 Paul Lamar

Stock o-rings can be purchased individually at Mazdatrix or your
friendly neighborhood Mazda dealer.
 WATER JACKET O-RING, INNER   N326-10-B71A
 WATER JACKET O-RING, OUTER   N326-10-B72
 O-RING - OIL SEAL OUTER   0820-11-341
 O-RING - OIL SEAL INNER   1202-11-343
Here is a rebuild parts list:
 http://www.mazdaspeeddevelopment.com/commonjobs.htm
 http://www.mazdaspeeddevelopment.com/partLists/869213b.html

Cheers
Cary

The stock silicone inner ring is $23 dollars alone. About 5 times the cost
of a Creavey. The Mazda outer ring is black rubber of some sort. My guess is it
is neoprene. Neoprene goes away at 200F. Silicone is good to 500 F.
Mazdatrix does not list the rings for the RX8.
http://www.mazdatrix.com/b2.htm

The stock rings are not reusable. Once the inner ring is used the teflon
on one side comes undone or un-glued. Why Mazda does not put Teflon on all
sides of both rings is a mystery to me.

Also you cannot buy from Mazdaspeed unless you race cars.
Kind of a dumb policy to me. SCCA member ship alone is $75
a year and it cost a lot to enter a race. High entry FEEs.
You also have to have a race car of course.  I have contacted
Mazdaspeed about this several times  and got nowhere.
What is the problem???!!! We race Mazda powered airplanes too.

See the screen capture jpgs.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.