Subject: V8 powered fatal aircraft crash
From: Rotary Engine
Date: 5/28/2011, 1:50 AM
To: AAA Put this in the To box

NTSB Identification: CEN11FA324
14 CFR Part 91: General Aviation
Accident occurred Saturday, May 07, 2011 in Conroe, TX
Aircraft: WOODWARD HAROLD L RAVIN 500, registration: N913RA
Injuries: 2 Fatal.

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed.

On May 7, 2011, approximately 0855 central daylight time, a Woodward Ravin 500 experimental amateur built airplane, N913RA, impacted forested terrain shortly after takeoff from Lone Star Executive Airport (CXO), Conroe, Texas. Visual meteorological conditions prevailed at the time of the accident. The personal flight was being conducted under the provisions of 14 Code of Federal Regulations Part 91. The pilot and student pilot rated passenger were fatally injured. The flight was originating at the time of the accident and was en route to Temple, Texas, for the airplane to be displayed at an aviation event.

According to CXO tower personnel, the pilot was cleared to depart runway 14 with a right turn on course. The airplane departed and as the pilot began his initial right turn he reported smoke in the cockpit. The pilot was cleared to land on any runway and giving the wind as being from 160 degrees at 8 knots. The airplane was observed to perform an approximate 240 degree right turn and crossed back over the departure runway before entering the left downwind leg for runway 14. While on the downwind leg of the traffic pattern the airplane was observed flying, “slow”, wings level, at an estimated altitude of 700 to 800 feet above the ground. While approximately 4,500 feet along the downwind leg the landing gear was extended. Shortly thereafter, the airplane started a descending left turn towards the closer runway 19. The airplane overshot the extended centerline to runway 19 and the airplane’s bank angle increased. The airplane continued in the descending left turn toward the runway until approximately 300 feet above the ground. At which point the airplane appeared to “stall” and impacted into forested terrain. A post impact fire ensued. Tower personnel reported that during the event they did not observe any smoke or flames coming from the airplane until impact.

A pilot rated eyewitness located near the crash site reported hearing what he described as an engine that was “screaming” and varying in RPM. When he saw the airplane it was flying “very slow” at an estimated altitude of 300 to 500 feet above the ground. As the airplane made a high bank angle turn back towards the airport the witness observed the nose and left wing drop before the airplane went out of sight. Seconds later he heard it impact trees followed by an explosion.

The airplane came to rest in an upright position about 1,600 feet out on the extended center line from the approach end of runway 19. The measured impact heading was 200 degrees magnetic.

------------------------------------------------------------
Sounds like they will never know what happened.

I am guessing. One possible scenario is the automotive clutch Bud used started
slipping causing the smoke and the “screaming” engine. The clutch disk
could wear rather rapidly due to normal high torque fluctuations
at high continuous power.

IMHO the TBO on an automotive V8 in aircraft use should be 300 hours.
Any piston engine can develop a crack in the critical parts leading to
a hand grenade failure without warning. The main purpose of the TBO is to
magnaflux the critical parts to detect cracks early before the engine
explodes. Through years and millions upon millions of hours of experience
and detail refinement the TBO on aircraft engines has increased to 2000 hours.

The TBO on my C182 engine was 1500 hours. By adding another torsional damper on the crankshaft the TBO was increased to 2000 hours. However unlike a piston engine in a car the aircraft crank and rods are made of the finest material possible. Only the best methods of manufacturing and finishing are used.

Parts in an automotive V8 are made as cheaply as possible as the average
required power is only about 40 HP despite a 400 HP rating.

We are so lucky the Wankel rotary does not see the same kinds of reverse loading
on the e-shaft and the rotor that are seen on a piston engine cranksaft and rods. Fatigue failures of the e-shaft and rotor are unheard of.


Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.