Subject: V8 powered fatal aircraft crash
From: Rotary Engine
Date: 5/30/2011, 8:39 AM
To: AAA Put this in the To box


  14 CFR Part 91: General Aviation
  Accident occurred Saturday, May 07, 2011 in Conroe, TX
  Aircraft: WOODWARD HAROLD L RAVIN 500, registration: N913RA
  Injuries: 2 Fatal.

  This is preliminary information, subject to change, and may contain
errors.
  Any errors in this report will be corrected when the final report
  has been completed.

  On May 7, 2011, approximately 0855 central daylight time, a Woodward
  Ravin 500 experimental amateur built airplane, N913RA, impacted
  forested terrain shortly after takeoff from Lone Star Executive
  Airport (CXO), Conroe, Texas. Visual meteorological conditions
  prevailed at the time of the accident. The personal flight was being
  conducted under the provisions of 14 Code of Federal Regulations
  Part 91. The pilot and student pilot rated passenger were fatally
  injured. The flight was originating at the time of the accident and
  was en route to Temple, Texas, for the airplane to be displayed at
  an aviation event.

  According to CXO tower personnel, the pilot was cleared to depart
  runway 14 with a right turn on course. The airplane departed and as
  the pilot began his initial right turn he reported smoke in the
  cockpit. The pilot was cleared to land on any runway and giving the
  wind as being from 160 degrees at 8 knots. The airplane was observed
  to perform an approximate 240 degree right turn and crossed back
  over the departure runway before entering the left downwind leg for
  runway 14. While on the downwind leg of the traffic pattern the
  airplane was observed flying, â<80<9Cslowâ<80<9D, wings level,
  at an estimated altitude of 700 to 800 feet above the ground. While
  approximately 4,500 feet along the downwind leg the landing gear was
  extended. Shortly thereafter, the airplane started a descending left
  turn towards the closer runway 19. The airplane overshot the
  extended centerline to runway 19 and the airplaneâ<80<99s bank
  angle increased. The airplane continued in the descending left turn
  toward the runway until approximately 300 feet above the ground. At
  which point the airplane appeared to â<80<9Cstallâ<80<9Dand
  impacted into forested terrain. A post impact fire ensued. Tower
  personnel reported that during the event they did not observe any
  smoke or flames coming from the airplane until impact.

  A pilot rated eyewitness located near the crash site reported
  hearing what he described as an engine that was
  â<80<9Cscreamingâ<80<9Dand varying in RPM. When he saw the
  airplane it was flying â<80<9Cvery slowâ<80<9Dat an estimated
  altitude of 300 to 500 feet above the ground. As the airplane made a
  high bank angle turn back towards the airport the witness observed
  the nose and left wing drop before the airplane went out of sight.
  Seconds later he heard it impact trees followed by an explosion.

  The airplane came to rest in an upright position about 1,600 feet
  out on the extended center line from the approach end of runway 19.
  The measured impact heading was 200 degrees magnetic.

  ------------------------------------------------------------
  Sounds like they will never know what happened.

  I am guessing. One possible scenario is the automotive clutch Bud
  used started slipping causing the smoke and the
  [WINDOWS-1252?]ââ?¬Å?screamingââ?¬Â  engine. The clutch disk could
wear
  rather
  rapidly due to normal high torque fluctuations at high continuous power.

  IMHO the TBO on an automotive V8 in aircraft use should be 300 hours.
  Any piston engine can develop a crack in the critical parts leading
  to a hand grenade failure without warning. The main purpose of the
  TBO is to magnaflux the critical parts to detect cracks early before
  the engine explodes. Through years and millions upon millions of
  hours of experience and detail refinement the TBO on aircraft
  engines has increased to 2000 hours.

  The TBO on my C182 engine was 1500 hours. By adding another
  torsional damper on the crankshaft the TBO was increased to 2000
  hours. However unlike a piston engine in a car the aircraft crank
  and rods are made of the finest material possible. Only the best
  methods of manufacturing and finishing are used.

  Parts in an automotive V8 are made as cheaply as possible as the
  average required power is only about 40 HP despite a 400 HP rating.

  We are so lucky the Wankel rotary does not see the same kinds of
  reverse loading on the e-shaft and the rotor that are seen on a
  piston engine cranksaft and rods. Fatigue failures of the e-shaft
  and rotor are unheard of.

  Paul Lamar

  It sounds like the pilot might have stopped flying the airplane, but
  instead was trying to save it. My training was that in case of fire,
  you get the airplane on the ground immediately, as you really don't
  know what's burning. I can understand the smoke could have been
  incapacitating, so that might have been the issue, but if it was the
  clutch burning, it seems unlikely somehow.

  Matt-

  I agree but people that build airplanes have so much invested in
  them (more than money alone) they appear to be reluctant to crash
  land straight ahead as we were all told to do in case of engine
  failure on take off. Here is a map of the area and there does not
  appear to be many clear fields other than on the airport itself. In
  the case of rotary crashes at least two fatals were caused by the
  pilots attempting to turn back. In both cases there were suitable
  fields straight ahead. One rotary crash was caused by engine seizure
  after the loss of all oil pressure due to a split cheap oil cooler
  and the other an interruption in the fuel supply due to a poorly
  designed fuel plumbing system.

  IMHO there is another more subtle factor. One is naturally reluctant
  to do a 180 and land downwind on a controled airport or busy
  airport. We had an incident at SZP where a pilot  had an engine
  failure in a Bonanza and successfully made a 180 and landed down
  wind. He slammed it in so hard on the 2500 foot runway it bent the
  spar and broke the motor mounts totaling the airplane but he was not
  hurt. He skillfully ground looped it when it looked like he was
  going to run out of runway at thew other end. I was standing 50 feet
  from the point of impact.

  I think people should practice 180's at altitude with the engine at
  idle. Just to get a feel of what the airplane will do. Note the loss
  of altitude.

  Paul Lamar

  --
  Persons close to the parties blame it on a bad oil line connection
  to the engine....not the clutch......FWIW.... Marc

  Why the "screaming" engine? Or did it sound like that all the time?

  Paul Lamar


  Re: Matt's comment about clutch burning unlikely. Yes unlikely, but
possible.  Hi-way haul trucks have got the brakes on fire coming down long
hills.  I worked on a Ford 1/2 ton that had stopped on the side of the road.
Questioning the driver/owner he said it slowed and stopped going.  The
engine ran fine.  The fellow said when he looked under the truckthere was
fire underneath.  When I removed the clutch cover, a couple ofhandfuls of
clutch fiber came out.  The flywheel, pressure plate, transinput shaft and
the back of the crankshaft were blue from the heat of theslipping clutch.
The trans input and the crank just had small spots.  Thefire was the release
fork boot burning from the radiated heat.  Surfaced theflywheel and put new
clutch in.  I also had to replace the trans inputbearing as this fellow
would shift into OD at 40MPH.  Ford dealer hadreplaced the noisy brg 3 times
previous.  Only 45K miles on the truck.  Hecame back two weeks later to see
if I had the clutch core.  Said he wastalking to his insurance agent and
they figured the fire burnt the clutchout.  There we go with the only thing
more dangerous than a dumby, is adumby that thinks he is smart.

  Dale Davies

  Burning brakes happened to me when I was driving a semi as a teenager.

  Paul Lamar



Wouldn't the clutch gripping strength be stronger than the other
components in the drive train?  I'm thinking rev up and pop-the
clutch..  And the clutch clamping surface is quite a distance from the
center of the shaft, lowering the slipping force (torque) required.
In automotive use, clutches fail when they are slipped, or engaged
suddenly.  If the clutch is healthy to start with (not worn out from
miles or abuse), it won't slip.  I think your 1/2 ton truck customer
rode (left his foot on) the clutch pedal.  That's a quick way to wear
one out - abuse.

As a side note, I went hunting a while back with a friend..  We were
in his pickup, he was driving.  I have never ridden with anyone that
slipped the clutch as much as this guy..  I mean, probably half the
time we were accelerating, the clutch was slipping.  I could tell he
was doing it by watching his leg/foot..  I have no idea how long that
clutch lasted, but it couldn't have been many miles.

I guess the crash airplane might have had the clutch
linkage/hydraulics mis-adjusted so that it didn't allow the clutch to
provide its full clamping pressure..  That brings up a thought...
Maybe airplanes with clutches (or anything that could slip) should
have a tachometer on both the prop and the engine..  And a little
circuit that keeps track of the ratio between them.  And which sets an
alarm if there's any discrepancy between the engine and prop RPM -
indicating slipping - which might not be immediately detectable to the
ear.

I understand that there may be torsional resonant loads at certain RPM
ranges, but I'd guess that they would threaten the prop shaft, or
output gear..  There's lots about this that I don't know - obviously.
Predicting the RPM at which resonant forces build doesn't seem to be
something that can be done by guessing or TLAR..  None the less, I
think the torsional loads would tear the center out of the clutch
before other failures, assuming proper engagement.

Matt-


Bud claimed the clutch damped the torsional pulses which implied it
had to slip.

Paul Lamar
--

I think it was a centrifugal clutch, no linkages.  The assumption is that
the resonant point is at low speed when the prop is not linked to the
engine.  There might be a normal spring center in the clutch disk also.
It is supposed to lock up at rpms where power is actually being used.

Murry I. Rozansky

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.