Subject: Fuel plumbing for rotary engines
From: Rotary Engine
Date: 6/4/2011, 11:31 AM
To: AAA Put this in the To box


The trouble with AN fittings is they are all male.
The trouble with AN hose ends is they are all female.
If you have three or more devices in series say; fuel pump,
filter and pressure sensor you wind up with a string of
stuff 2 feet long. Each device must be separated by a hose
or pipe. Each hose or pipe is a minimum of 2 or 3 inches long.

The trick is to use a 3D fuel rail in reverse.

Here is a set up where there are two tanks. Each tank has
a fuel pump. Each fuel pump has a fuel filter.

The up side to this is if one tank, filter or pump fails you
have a back up in the other tank, filter and pump.
There are scenarios where this does not work out well but
any system has bad scenarios.

You merely select tanks with a toggle switch on that tank's fuel
pump. Fuel is prevented from going to the other tank
by a one way valve in the hi pressure Walbro pumps.

Unfortunately with any EFI systems fuel must always be returned to the
tank it is drawn from or in some cases fuel can be pumped
over board through the vents. With this system an electric
actuated valve is used to select which tank the fuel is returned
to.

A single common sump tank can be used but unless it is
cooled the fuel will heat up due to being continuously re-circulated
through the fuel rails on the engine.

I digress.

Here is the fuel rail in reverse trick.
Explained by the drawings.

Paul Lamar

not entirely true.

look here...

http://www.aeroquip.cc/fcm2971fbm2971-06x-06.aspx

and here...

http://www.aeroquip.cc/fcm2915fbm2915-06x-06.aspx

You may find a solution that will be both compact and simple.

William Mason

I am sure I won't. :)
In effect I have no fittings at all :)
Just a block of aluminum.

Try PegasusAutoRacing.com
They have the largest collection of AN fittings I have found so far.

Paul Lamar

!@#$%%^ (cursing :)

The limitations of 3/8 aluminum tubing plumbing bit me today. I was not
able to get a simple right angle connection in the space available
due to the limitations of flaring tools and the fact the sleeve will
not slide around 90 degree bends. I used a lever tube bender.

wont-work.jpg

Ideally if one were starting from scratch one would move the fuel pump
back and inch or two but I did not want to punch yet another hole in
the structural fuse skin.

Plan B: The next thing I tried was the 270 degree helix trick. A
lever tube bender will not bend 270 degrees. Max bend is 180
degrees. So I had to go with
the spring bender. The problem with that is you can not get the
spring off the
tubing after it is bent 270 degrees unless it is bent around a 2
inch diameter or larger rod or pipe. Even 2 inches is  marginal.
That started to get too close to the control mechanism and the aft
panel. I spent all day on it and
it was a pain in the butt.

270-degree-trick.jpg

Plan C: to be tried next week is connect the right filter to the left
fuel pump and the left filter to the right fuel pump next week when
I get some
more tubing. Fortunately there is room under the controls. Plan-C.jpg

It is tough squeezing all this stuff under the floor of an RV4,

Paul Lamar



I have to admit that I do really like your fuel rail idea, though
probably somewhat heavier.  Hate to say I told you so about things
becoming more difficult than expected, so I won't :-)  Have I ever
mentioned how much I hate working with aluminum line...  Too bad it is
just so light weight, strong, slim, and dirt cheap compared to hose.

I like option C the best anyway.

-- 
David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net

By spending more money on machining... the reverse fuel rail could be made much lighter. I consider this version the prototype. Jim wanted to cut the weight
but I did not want to spend the extra money just yet.

Aluminum line certainly has a steep learning curve. Better benders and flaring tools would help. A helix bender both right and left hand would be a major break through. One could unscrew the tube from the bender. My Rhino computer is out
at the hangar so I'll do a 3D of what I have in mind. When by bank account
is some what restored I might have Jeff D make me one.

The flaring tool would be smaller and easier to use if it was
dedicated to just 3/8" tube alone.

Jim and I also developed a better beading tool for 1.5 and 2 inch aluminum tubing. Same goes for that. We might build and sell some of them if people want them. I am not happy with the Earl's beading tool.


Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.