Subject: The rotary goes Reno racing.
From: Rotary Engine
Date: 6/20/2011, 8:15 PM
To: AAA Put this in the To box

Dave Leonard told me he was going to Reno this
past week with his turbo RV6 for the 2011 PYLON RACING SEMINAR.


http://n4vy.rotaryroster.net/


How did it go Dave?

Paul Lamar



 Hey Paul,

 I had a great time!  Qualified as a pilot for the races in
Sept.  Plane
 did really well, except I was leaking some combustion gasses
slowly into
 the coolant and had to cool and burp the system between every
flight.

 I mostly didn't push the plane too hard. Fastest lap that I
timed was
 217 mph.  That was 40 inches MAP and about 6700 RPM.  Another
lap was
 212 mph at 38 in MAP and 6500 RPM.  I figure that I will push
it up as
 high as 45 inches in Sept.

 In comparison, a 180 hp RV-8 (faster airframe) with a c/s prop was
 running about 192 mph around the course at WOT and 2600 rpm.
 The F1
 Rockets and Super-6/Super-8 were running between 230 and 245
mph (O-540 CI
 [250 to 300 HP] or similar engines with usually shorter wings).

 Awesome experience.

 Bob Mills did a better write up:
 http://www.vansairforce.com/__community/showthread.php?t=__73286
<http://www.vansairforce.com/community/showthread.php?t=73286


 --
 David Leonard

 Turbo Rotary RV-6 N4VY
 http://N4VY.RotaryRoster.net <http://n4vy.rotaryroster.net/
 http://RotaryRoster.net <http://rotaryroster.net/


 Wonderful news Dave. Not bad for an RV as the relatively low
aspect RV
 wings
 creat more drag in a high G turn.  It is over 5000 feet up there so
 I am sure your turbo helped a lot.


This is how to make people sit up and
take notice
of rotary installations in aircraft. The history of air racing
bears this
out.

Well, I'm not sure that the uninformed will be very impressed.  They
will only notice that I am in last place.  A few knots are not going
to help much.  During race week I will probably go to 45" for at
least the qualifying run, and post a qualifying time above 220,
maybe as much as 230mph.  But either way, I will probably be dead
last and a few more knots are not going to matter much one way or
another.

But the informed observer might take note.  I was much closer to the
speed of the super-6 than to the RV-8.

I have been kicking around the idea of installing an ADI system.  Or
maybe a water spray bar for the inter cooler.  I was seeing 55 deg C
during the race, which is not too bad but I would feel better if I
got it down some.  Does anyone have experience with ADI?

--
David Leonard

Drag reduction is far more fruitful than increasing power.
Are you using all the racing tricks like go fast tape on all the seams?

Steve Beckham, do you have Tracy Saylor's phone number or email address?


Paul--I don't.  I failed to put the contact information for Tracy S. , Dave
A. and the other guys it in my electronic files as they were accumulated
over the years.  With the house being remodeled the hard copies of all that
reference stuff is in storage.   Unfortunately, it appears several of those
boxes, including the Hoerner books, was commingled with various other junk
by my "domestic associate" and appear to have been inadvertent discarded.

Agree with you about the recommended focus on drag reduction.  It is the
most  affordable of the speed mods.   And not just the obvious external
airframe details.  Cooling drag as well is a very big deal as velocity
increases.   The liquid cooled engines provide the opportunities for
significant reductions in cooling drag not possible with air cooled engines.
Steve Beckham

Too bad about the loss of that that stuff. The Hoerner books are worth well over $100 each.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.