Dave Leonard told me he was going to Reno this
past week with his turbo RV6 for the 2011 PYLON RACING SEMINAR.
http://n4vy.rotaryroster.net/
How did it go Dave?
Paul Lamar
Hey Paul,
I had a great time! Qualified as a pilot for the races in Sept. Plane
did really well, except I was leaking some combustion gasses slowly
into the
coolant and had to cool and burp the system between every flight. I
mostly
didn't push the plane too hard. Fastest lap that I timed was 217
mph. That
was 40 inches MAP and about 6700 RPM. Another lap was 212 mph at 38
in MAP
and 6500 RPM. I figure that I will push it up as high as 45 inches in
Sept.
In comparison, a 180 hp RV-8 (faster airframe) with a c/s prop was
running
about 192 mph around the course at WOT and 2600 rpm. The F1 Rockets and
Super-6/Super-8 were running between 230 and 245 mph (O-540 CI [250 to
300
HP] or similar engines with usually sho
Awesome experience.
Bob Mills did a better write up:
http://www.vansairforce.com/__community/showthread.php?t=__73286
<
http://www.vansairforce.com/community/showthread.php?t=73286
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net <
http://n4vy.rotaryroster.net/
http://RotaryRoster.net <
http://rotaryroster.net/
Wonderful news Dave. Not bad for an RV as the relatively low
aspect RV
wings
creat more drag in a high G turn. It is over 5000 feet up there so
I am sure your turbo helped a lot.
This is how to make people sit up and
take notice
of rotary installations in aircraft. The history of air racing
bears this
out.
Well, I'm not sure that the uninformed will be very impressed. They
will only notice that I am in last place. A few knots are not going
to help much. During race week I will probably go to 45" for at
least the qualifying run, and post a qualifying time above 220,
maybe as much as 230mph. But either way, I will probably be dead
last and a few more knots are not going to matter much one way or
another.
But the informed observer might take note. I was much closer to the
speed of the super-6 than to the RV-8.
I have been kicking around the idea of installing an ADI system. Or
maybe a water spray bar for the inter cooler. I was seeing 55 deg C
during the race, which is not too bad but I would feel better if I
got it down some. Does anyone have experience with ADI?
--
David Leonard
Drag reduction is far more fruitful than increasing power.
Are you using all the racing tricks like go fast tape on all the seams?
Steve Beckham, do you have Tracy Saylor's phone number or email address?
Paul--I don't. I failed to put the contact information for Tracy S. ,
Dave
A. and the other guys it in my electronic files as they were accumulated
over the years. With the house being remodeled the hard copies of all
that
reference stuff is in storage. Unfortunately, it appears several of
those
boxes, including the Hoerner books, was commingled with various other
junk
by my "domestic associate" and appear to have been inadvertent discarded.
Agree with you about the recommended focus on drag reduction. It is the
most affordable of the speed mods. And not just the obvious external
airframe details. Cooling drag as well is a very big deal as velocity
increases. The liquid cooled engines provide the opportunities for
significant reductions in cooling drag not possible with air cooled
engines.
Steve Beckham
Too bad about the loss of that that stuff. The Hoerner books are worth
well over $100 each.
Paul Lamar
Last check I made searching Alibris and Amazon, Heorner book was $500.
C. Smith
Darcorp / Dr. Roskam sells the Hoerner books for less. They also them
at their Oshkosh booth in the past:
https://oscommerce.darcorp.com/index.php?cPath=1
~Cary
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.