Subject: The rotary goes Reno racing.
From: Rotary Engine
Date: 6/22/2011, 6:37 PM
To: AAA Put this in the To box


 Dave Leonard told me he was going to Reno this
 past week with his turbo RV6 for the 2011 PYLON RACING SEMINAR.


 http://n4vy.rotaryroster.net/


 How did it go Dave?

 Paul Lamar



 Hey Paul,
 I had a great time!  Qualified as a pilot for the races in Sept.  Plane
 did really well, except I was leaking some combustion gasses slowly
 into the
 coolant and had to cool and burp the system between every flight.  I
 mostly
 didn't push the plane too hard.  Fastest lap that I timed was 217
 mph.  That
 was 40 inches MAP and about 6700 RPM.  Another lap was 212 mph at 38
 in MAP
 and 6500 RPM.  I figure that I will push it up as high as 45 inches in
 Sept.
 In comparison, a 180 hp RV-8 (faster airframe) with a c/s prop was
 running
 about 192 mph around the course at WOT and 2600 rpm.  The F1 Rockets and
 Super-6/Super-8 were running between 230 and 245 mph (O-540 CI [250 to
 300
 HP] or similar engines with usually sho

 Awesome experience.

 Bob Mills did a better write up:

http://www.vansairforce.com/__**community/showthread.php?t=__**73286<http://www.vansairforce.com/__community/showthread.php?t=__73286

<http://www.vansairforce.com/**community/showthread.php?t=**73286<http://www.vansairforce.com/community/showthread.php?t=73286


 --
 David Leonard

 Turbo Rotary RV-6 N4VY
 http://N4VY.RotaryRoster.net <http://n4vy.rotaryroster.net/
 http://RotaryRoster.net <http://rotaryroster.net/


 Wonderful news Dave. Not bad for an RV as the relatively low
 aspect RV
 wings
 creat more drag in a high G turn.  It is over 5000 feet up there so
 I am sure your turbo helped a lot.


 This is how to make people sit up and
 take notice
 of rotary installations in aircraft. The history of air racing
 bears this
 out.

 Well, I'm not sure that the uninformed will be very impressed.  They
 will only notice that I am in last place.  A few knots are not going
 to help much.  During race week I will probably go to 45" for at
 least the qualifying run, and post a qualifying time above 220,
 maybe as much as 230mph.  But either way, I will probably be dead
 last and a few more knots are not going to matter much one way or
 another.

 But the informed observer might take note.  I was much closer to the
 speed of the super-6 than to the RV-8.

 I have been kicking around the idea of installing an ADI system.  Or
 maybe a water spray bar for the inter cooler.  I was seeing 55 deg C
 during the race, which is not too bad but I would feel better if I
 got it down some.  Does anyone have experience with ADI?

 --
 David Leonard

 Drag reduction is far more fruitful than increasing power.
 Are you using all the racing tricks like go fast tape on all the seams?

 Steve Beckham, do you have Tracy Saylor's phone number or email address?


 Paul--I don't.  I failed to put the contact information for Tracy S. ,
 Dave
 A. and the other guys it in my electronic files as they were accumulated
 over the years.  With the house being remodeled the hard copies of all
 that
 reference stuff is in storage.   Unfortunately, it appears several of
 those
 boxes, including the Hoerner books, was commingled with various other
 junk
 by my "domestic associate" and appear to have been inadvertent discarded.

 Agree with you about the recommended focus on drag reduction.  It is the
 most  affordable of the speed mods.   And not just the obvious external
 airframe details.  Cooling drag as well is a very big deal as velocity
 increases.   The liquid cooled engines provide the opportunities for
 significant reductions in cooling drag not possible with air cooled
 engines.
 Steve Beckham

 Too bad about the loss of that that stuff. The Hoerner books are worth
 well over $100 each.

 Paul Lamar

 Last check I made searching Alibris and Amazon, Heorner book was $500.
 C. Smith


Darcorp / Dr. Roskam sells the Hoerner books for less.  They also them
at their Oshkosh booth in the past:

https://oscommerce.darcorp.**com/index.php?cPath=1<https://oscommerce.darcorp.com/index.php?cPath=1
~Cary

Here is a video that I took on the last day:

http://www.youtube.com/watch?v=6W0_l6Cjo-0

-- 
David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net


Cool :)

What water and oil temps were you seeing Dave?

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.