Tom/norpro
Good price Tom.
If you drove this with a 1 to 1 cog belt drive a very simple outboard motor
type CD ignition could be easily added by swapping out a couple of coils
180 degrees apart for 300 volt units.
Save one for me Tom.
Paul Lamar
I'll take one too, where do I send the money?
Craig Smith
I would like to have one too.Just tell me how and where to send the money.
Michael Hart
Here is Tom's email address.
http://www.4norpro.com/generators.html
tomm@4norpro.com<mailto:tomm@4norpro.com>
Looks like these are used or one or more of the coils may have failed.
-----------------------------------------------------------------------
Here is a new Kubota for $106
Same type of magnet type of alternator. No field winding.
14 amps 3.12 pounds.
http://www.discountstarterandalternator.com/p-655-new-alternator-kubota-tractor-15531-64013-15531-64016.aspx
http://tinyurl.com/3fx7qxb
Two of these with modified for CD ignition one for top plug and one for bottom
plug would give dual independent ignitions and alternators.
One or two cog belts.
There is no regulator inside the unit
so an external regulator will be required as they are designed for low RPM
engines. ALTERNATOR REGULATOR 1K531 - 64602
http://groups.yahoo.com/group/AirVW/message/14115
"I'm getting 14.5 volts from 1200 engine rpm with a stock VW pulley, about 6"
diameter, all the way through 3300rpm." No load is mentioned.
Gil
I am not sure they will run to 7500 RPM so test them in a safe way because they
could blow up. A wrap of carbon or Kevlar uni would be a good idea.
http://www.iowamotorparts.com/kubota_alternators.htm
Lots of options here.
Paul Lamar
Here is Tom's email address.
http://www.4norpro.com/generators.html
tomm@4norpro.com<mailto:tomm@4norpro.com>
Looks like these are used or one or more of the coils may have failed.
Paul Lamar
Where do we find out about the details? I don't see this listed on the website.
If they are broken or are not fully operational, that should be info up front.
C. Smith
Paul:
Where would you like it sent and how? I would suggest the USPO $5 box if
you are not in a hurry. My address is norpro
Att. Tom
385 town st
East Haddam ct 06423 or I can be reached
at860-873-0100-ext.0 and ask for Tom. We do take credit cards but not amx.
Tom/norpro
Tom, are these new or used? Are they guaranteed to work?
Paul Lamar
All:
They are units that have come back for Isuzu warranty consideration. All
were on new engines and if the battery is hooked up backwards on installation
the regulator will pop. These have the add on regulator that are screwed on the
back. They have been tested and match the same ohm readings thru the coils as
well as to ground. They test the same as a brand new one. I will warrantee them
for 90 days. The external regulator that works on the Kubota, Yanmar and Isuzu
will work on this. I am sure Paul can come up with a $10 regulator that will
work with it. We also have new take off's that were removed to convert the
engine to 24v for $150 that will include the regulator and a mating plug plus a
wiring diagram. Without a regulator it weights 4lb and with 4 3/4lb. I have
sold a bunch to the Corvair crowd. If you have any other questions I would be
glad to answer them. If Paul would like I will send him one for inspection and test.
Tom/norpro
All:
Craig smith implied that I was trying to hide something, I take no offence
to it. I would like to set the record straight. I thought I was replying to the
Honda post for used parts. I thought by offering the group something that I
believe is better and currently available on the market rather than a used 70's
set of coils for a Honda or the outrageous price of Harley parts.
I see I screwed up when I offered Paul a unit to test, I need to send him a
complete one to compare readings. So the offer is for 2 units. The manufacture
is Kokusan Denki part# GP9905 and Isuzu part# 8970489701. If there is any other
info anyone would like I would be glad to provide it.
Tom/norpro
Thanks for the offer Tom.
I'll send you my shipping address by PRIVATE email.
I'll set it up on the bench and test it for out put current.
Paul Lamar
To set the record straight, I was not trying to imply anything of that nature at
all. I was responding to the comment made by Paul
"Looks like these are used or one or more of the coils may have failed.
Paul Lamar"
No offence intended. I didn't see anything about these coils, so I wanted
clarification about condition.
C. Smith
Tom sent me a couple to test.
I set one up in the CCM and it put out 9 volts AC at about 5800 RPM.
15 volts AC at 9840 RPM. This unit is best used with a belt drive.
You will need some diodes to convert the AC to DC.
It could be used direct drive as part of the flywheel if you re-wound the coils
with slightly smaller wire. Voltage would go up at 5800 RPM but there would be a
slight loss in current output.
As a source of 300 volts for a CD ignition system perhaps one or more custom
wound coils mounted on the outside of the magnet drum would work. The magnets
are very powerful indeed. When you turn it by hand you can feel the magnetic
attraction for the metal coil cores.
Tom also sent me one with attached diodes and voltage regulator which I have not
yet tested.
The unit weighs about 4 pounds which is half the weight of the stock Mazda RX7
alternator however the current output is half too.
Paul Lamar
I am not sure about the RPM numbers yet.
I misplaced my optical tac. They could be 1/4 of the numbers above since there
are four magnets.
Tom, what is the pulley diameter on the Isuzu diesel?
What is the Isuzu diesel RPM?
Paul Lamar
Paul:
The crank drive pulley is 115mm and the high speed generator turns 3800 rpm
no load.
Tom
That is 4.5 inches so I am probably off by a factor of two.
9840 is really about 4920.
And 5800 is really about 2900 RPM.
I was incorrectly going on the frequency of the AC wave coming out
the wires. In that case this would work direct drive on a rotary. I'll draw
something up integrated with the flex plate.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.