Subject: Polishing aluminum airplanes
From: Rotary Engine
Date: 7/2/2011, 7:24 PM
To: AAA Put this in the To box


 I decided to polish the RV4 rather than get it painted.
 I have more time than money. I have other uses for
 the 7 to 1OK.

 Doing it by hand is very very tedious I found out rather
 rapidly. I got some white aluminum polish at the auto parts
 store that worked well on the shiny alclad. I bought
 another brand from Rutland tool but it was the same stuff.
 Worked about the same

 There were these gray strips on the rivet lines and somebody told me
 that was caused by the the plastic protective sheets Van glued to the
 Alclad. You stripped it off where the rivets went and the bare aluminum
 turned gray on its own over time. That was another problem entirely.
 Nothing
 seemed to work. I tried 320 grit flap wheels which took it off alright but
 left microscopic scratches on the aluminum the white polish had a hard
time
 with. Same for scotch brite. Too coarse. I then tried 3000 grit sand paper
 by hand and that worked only slightly better but was extremely tedious.

 I saw a guy on Youtube polish an aluminum diesel truck tank in 20 minutes
 or most of it anyway. He used what we used to call a body grinder. I had
 3 HP versions. One that was close to 40 or 50 years old.

 He actually used two with buffing wheels. One had one type of polish
 and the other another type of polish. I went to Harbor Fright to get
 a buffing wheel and they had several different compounds for polishing
 aluminum. They had the white which looked like the other two whites
 I already had. They also had gray which they called a fast cut compound.

 Bingo! It worked like a charm with the 8 inch spiral sewn buffing wheel
 mounted on the body grinder. In an hour I had half the lines gone on one
 side
 of the fuselage. Another hour to buff it out. The type of buffing wheel
 is also critical. One needs the spiral sewn. No replacement for
 displacement
 the 3 HP body grinder is also essential.

 Saved myself $7000. Does not make sense to have a $3000 rotary engine
 and spend $7000 on a paint job :)


 Paul Lamar


 Hey! Nice job.. I really admire that. I polished my plane once.. Then I
 painted it two months later... :-)

 -- David Leonard

 Turbo Rotary RV-6 N4VY
 http://N4VY.RotaryRoster.net <http://n4vy.rotaryroster.net/
 http://RotaryRoster.net <http://rotaryroster.net/



 I polished mine with a grinder with polishing wheel that I got from
 Harbor Freight. THere's a guy in the next hangar over with a beautiful
 Swift that he polished with a fancy dual wheel polisher- two wheels to
 counteract torque- they cost dearly though. This guy married for money,
 has about 5-6 airplanes in his two hangars.

 I won't be painting mine for a while, if ever. If I do, I'll do it myself.

 Brian Trubee


Beautiful Work Paul.  Years ago a friend went to Canada
and brought home a Chipmunk still in RAF colors.  Several of
us worked many days stripping it to bare metal and then polishing
it out - it was well worth the sweat.  We also used something akin
to "Semichrome" polish on the bubble canopy; Made it look like brand
new.

roger

Paul,  on motorcycles we use jewlers rouge on the buffing wheel and then
semichrome (comes in a toothpast like tube).  BE CAREFULL USEING A 3 HP
ANGLE GRINDER. In the long history of bad ideas this is near the top of the
list. The slow speed ones like Souix are nice but turn 5400 RPM  and many
like a Black and Decker wildcat  are 9000RPM.  You are converting 3 HP or 15
amps at 110 volts into mostly heat.  This heat can warp\ buckle aluminum
sheat into unairworthy junk. If you must have a large power tool the dual
wheel buffers run at a much slower speed and generally half the amp draw.
They are  also lighter to hold up against something for hours at a time. If
you wouldn't use it to polish your RX8 you shouldn't think it is a good
choice for aluminum sheet metal. There are sealers that greatly slow
reoxidation of the aluminum . Also only the original polishing takes
forever, the touch up repolishing is only a fraction of the work.


   george
grimes

Good point on the RPM as the fabric wheel is only good for 3600.
Mine is two speed and I run it on the low speed. It is only on one spot
on the aluminum for a fraction of a second because that is all it takes
to get the oxidation off. Heating is not a problem. One can test that
by putting ones finger on the spot just polished.

Don't confuse the buffing wheel with a large flat buffing round pad on
a conventional  polisher. Apples and oranges. The buffing wheel
has far higher pressure.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.