Subject: EVINRUDE 50 HP STATOR AND FLYWHEEL
From: Rotary Engine
Date: 7/3/2011, 4:06 PM
To: AAA Put this in the To box


 Paul I received the flywheel for for the stator 173-1232 and i did
 machined to the maximum on the outside diamete and i leave .330" wall
 thickness so it can be easy adaptable to the spline hub at 6"outside
 diameter by using rivets same as Tracy.The problem is the inner shaft hub
 on the flywheel non machinable  very hard temper so i did drilling all
 around to get it out.I weight the flywheel after cleaned and show about  3
 lbs on my bathroom scaleI should receive the stator within a day.The
 outside diameter of the flywheel can be reinforced with a stainless steel
 ring or unicarbon fiber machined and balance,or stainless steel angle ring
 to fit the o.diaI do have to complete the machining for the flywheel  on a
 bigger lathe mine is to small regarding the propshaft i can do some of the
 machining and get the rest finish by machine shop.I am waithing to receive
 a wood lathe so i can start to built the wood housing pattern for the prop
 drive.I have an idea to bolt the flywheel behind the Tracy prop flange and
 have a circular flange on his housing to hold the stator,the stator
 dimension is 6"o.dia by 4 1/16"i.dia and about 1 3/8"thick at coils
 location it might fit on Tracy housing it look the right size may be i am
 wrong so you can check the dimention on his housing with my design i do
 have to install on the rotary side flywheel (High RPM)The stator charging
 output is 6 amps.I bought the flywheel for $30.00 and $70.00 for the
 stator plus shipping on EBay the flywheel is for 50 and 55 hp up to 1975
 few mores  availables on EBAY

Jean Prudhomme

EVINRUDE 50 HP STATOR AND FLYWHEEL

http://skydrive.live.com/redir.aspx?cid=83c64c1851927d22&page=browse&resid=83C64C1851927D22!196&type=5&Bpub=SDX.Photos&Bsrc=Photomail&authkey=IiY4ytqj1Xk%24

Jean,
I have a 14 inch engine lathe with carbide tooling . If we can help, let me
know,
Milo

                  Milo Sure you can help me on machining and i am wondering if you do have a
milling machine also if not would you interested to machine the propshaft and if
you don't have milling machine i can get done by regular machine shop.I want to
know how much you will charge me .For the stator i need the tracy aluminum
flywheel plate with all dimensions to adapt the evinrude flywheel and the spline
hub but for you guys with tracy gearbox it will be easy to adapt to the flywheel
housing on behind prop flange and can be better at low rpm for centrifugal
force,the stator can be hold with an aluminum plate with 4 sides lips which can
be bolted to housing side ribs.The flywheel can be sandwich between the rear
propflange and prop bushing but it have to be extended about .250" and .250"
alum backplate it have to be riveted to the back flywheel and have a double
small recess to be aligned with the prop flange. You see Milo my big problem is
to get the propshaft drilled and machined at rough side so i can finish on my
small lathe, my lathe can handle 9" by 24" but the chuck can hold about 5" this
is why i need the rough machined or get it all done by someone. Paul could you
send me the Tracy dwg for the flywheel plate
Jean Prudhomme

Here is all I have on Tracy's damper plate.
Michael Hart has my old damper plate.
Other people may have one disassembled that they can measure.
Paul Lamar



Paul Do you know the RX8 Engine flywheel is different then the RX7 the holes spaceng is a bit over 10" center to center for holes bolting on the rx8, for the first look it will fit just fine for the Stator wheel,as per your sketch you show 4.45" radius it will be tight for the outside dia stator rotor on the RX&but i will see when i get the plate.


Jean Prudhomme


I did not know that.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.