Subject: Ok Here are the important flywheel measurements
From: Rotary Engine
Date: 7/15/2011, 5:56 AM
To: AAA Put this in the To box


 I finally got to the hangar and measured out my S5 turbo flywheel and the
 remains of my S5 flexplate.  The results are very encouraging, even as good
 as the possibly could be to make the swap, but I only had ten min at the
 hangar before I had to leave to pick up my daughter from daycare, so they
 are one try and slightly sloppy... I make no guarantees.  The height
 measurements of the flex plate were particularly suspect because, well,
 mine
 is all warped and broken.

 *Ring Gear Diameter* - Perfect fit.  As we suspected, same size, same tooth
 spacing.

 *Ring Gear Fore-Aft Placement* - As measured from the underside of the big
 nut. (for all further reference, aft means aft in the CAR).  The flex plate
 puts the aft side of the ring gear 1.290 inches from the front of the big
 nut. The flywheel puts it 0.913.  So the flex plate puts the ring gear
 (appx) 0.377 in. further aft.  This is actually fortuitous because it just
 so happens that the ring gear thickness is .365 ...    So all we have to do
 to fix the discrepancy is weld and extra ring gears onto to the flywheel
 ring gear and there will be teeth that the starter can reach:(bottom of the
 page.. the cost $80)
 http://mazdatrix.com/flywheel.**htm <http://mazdatrix.com/flywheel.htm
 It may also be possible to fix the discrepancy by changing the starter...
 will look into that.

 *Damper Plate Placement* - On the flywheel, the mounting surface is proud
 (or aft) of the ring gear.  On the flex plate, the mounting surface is
 recessed (or forward) from the ring gear. And it all pretty much works out.
 That position on the flywheel will vary somewhat depending on which
 flywheel
 you have and how much wear you have on the clutch slip surface. But on my
 (I
 assume well-worn) flywheel the placement was 0.965 while the flex plate was
 0.950.  Pretty damn close and given measurement error it might me meant to
 be right on.  Or, any difference could be made up by trimming down the
 spline on the damper plate or removing or adding spacers between the two.

 So in my mind, a flywheel is the way to go.  Stout, easy to get, pick your
 weight, only mods seem to be drilling the mounting holes and welding on a
 second gear ring.

 --
 David Leonard

 Turbo Rotary RV-6 N4VY
 http://N4VY.RotaryRoster.net
 http://RotaryRoster.net


 You are not seriously considering a 30 pound cast iron flywheel are you? :)
 If aluminum how must does it cost?
 Here is what the new PowerSport used.

 ------------------------------**-------------------

 OK I see you gave the Mazdatrix link to the aluminum flywheel.

 You don't have to weld on another ring gear which might damage
 the aluminum. Just space the starter aft (car). In the aircraft move
 it forward with a spacer. Since the ring gear is now forward (aircraft).

 Will Tracy's damper plate still fit?



 Paul Lamar


Mazdatrix has a light weight steel flywheel that weighs 18lb (including
counter weight) and costs $350.  Aluminum weighs 12 lbs and costs $400.
There is an aftermarket chrome-molly for $200.

I think you mis-understood the direction of the ring gear.  The flywheel
will move it .37 further aft (aircraft) so the starter gear won't reach
unless you add the extra ring gear.

the adapter plate fits right in place, depending on the wear pad thickness.

-- 
David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net


Cut down the starter and pocket Tracy adapter plate for the
starter. Get Jeff to do it or if he does not have time
Jim Poole can do it up here.

I like the chrome molly flywheel. Makes a lot better sense than
aluminum. Aluminum is way more prone to fatigue cracking than chrome molly.


Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.