Subject: Damper and flex combined
From: Rotary Engine
Date: 7/18/2011, 10:05 AM
To: AAA Put this in the To box


This reduces the number of parts.

The flex plate can be .090" thick 4130 or anything up to 1/4 inch.

The damper plate has been reduced to one ring part instead of
a large thick Al plate four Al blocks and 16 rivets.

A large ring with twelve 1.375 inch holes easily
drilled on an NC machine. Only four of which are
used fro the rubber bushings. The rest are there to save
weight.

The Ford auto TX part is turned around 180 degrees
to nest inside the flex plate. Only 10 steel
10-32 screws are used to bolt it to the damper ring
instead of 20 rivets.

The rubber bushings and washers are the same.

No need to move the starter or change the damper
design as I suspect would be required with the RX8 flex plate.

What do you think Dave?

Paul Lamar
Looks elegant to me.  Does the "Ford auto TX part" seat into the guide
  bearing in the E shaft?

Mark LaPierre
The input shaft with the sun gear does that.
  The Ford part has an internal spline that runs on the input shaft.
The Ford part is the same as Tracy uses now and it can be salvaged
and re  used by drilling out the rivets.
Paul Lamar
If you decide to make a run of these, count me in for one. Or whatever
  solution is decided to be best.
  C. Smith
This is going to hinge on what Dave says as he is our
  chief part Zerstörer right at the moment.  Mark Steitel is
  second in command with a p-port 3 rotor now flying.
  I'll take over when I get a P-port in the RV4.
Paul Lamar

LOL, Thanks Paul.  Nice work.  I really like the idea of a more purpose
built and dampened connection.  In your design, I don't understand
where the dampening is coming from.  If it is all the big holes in
the damper plate, at first that seems like a good idea then I think
than maybe it will make it too firm of a connection unless the the
rubber is really soft.

BTW, I measured Tracy's rubber dampers today:  1/2 inch.

So I had previously narrowed it down to 2 options, now we add your
design as a third:

1) Paul's design.  Nice, elegant, probably first choice if we spent some
time hashing out the details.  The cost and work will invariably be higher
than the off-the-shelf solutions. Cost ??,  Work??

2)  RX8 Flex plate.  Very easy solution.  Requires an intermediate
plate for adaption then it is good to go.  I went to an online
machine shop and we could get the plate for about $50 (I have it all
designed and ready to ship, thanks to Jeans measurements).  The only
other work would include welding if you wanted but 4 bolts alone
would work fine, and an hour's work with a die grinder to bevel the
other side of the gear ring.  Cost - $160 for the flex plate and $50
for the intermediate adapter.  If welded, this would be exceedingly
stiff and light weight. (5 lbs for the flex plate, 1.4 lbs for the
intermediate plate, and 0.8 lbs for bolts if you didn't want to
weld.) So this is the lightest weight, lowest cost, and least work
solution!  But it only makes moderate improvements in durability
over Tracy's current design - which has done very well and moderate
improvements should be all we need.

3)  Off the shelf flywheel.  Requires drilling some holes in the
flywheel, and possibly machining it to accept the bolts on the back
(because of non-flat surface) and possibly reduce the height of the
clutch surface. Also requires wielding on a ring gear to fit the
current starter, or (only if we are lucky) switching to a different
starter.  Durability seems to be the toughest of the lot, but with
aftermarket stuff you never really know.

So, I am just a little push from diving into option #2. with option
3 as the favorite if the turbo starter happens to fit...  Kelly has
one on the way to test.

--
David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net <http://n4vy.rotaryroster.net/
http://RotaryRoster.net <http://rotaryroster.net/

The damping is EXACTLY the same as the damping in Tracy's
design. At this point in time we are only using four holes.
I don't believe in fixing something that is not broken.
We do have softer rubber bushings available. Down to 40
durometer if you want to try them but I don't recommend
it at this time. The ones we are building now are
about 70 durometer. If durability of the silicone is
a problem we can go to more holes.

Is the RX8 ring gear the same diameter as the 13B?

I did not think it was. It just looks larger.
If it is you will need to relocate the starter.

No holes down near the clamp and the thicker (.090")
material is a big plus.

Paul Lamar


If you are going to make your own flex plate; you could cut just a disc to
bolt to the balance weight and the damper bolts to it.
Then mount a smaller flex plate on the back of the crankshaft pulley and make
a bracket to mount the starter. It may cost a bit of weight, but that would be
shifted towards the CG. It might even be possible to mount the motorcycle
generator on it transferring that weight also to the center.

Dale Davies

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.