It was 85 F to 90 F and I taxied the RV4 up
and down the length of the runway twice.
Tarmac temperature was 114 F.
The engine coolant never got over 160 F! I am amazed.
Mike Wills did everything right. The cooling duct/diffuser
shields the rad from engine heat.
Taking the slack out of the rudder cables where they link to
the tail wheel also worked very well. The RV4 responded to the
slightest movement of the rudder pedals. We had a strong
gusty cross wind today.
Paul Lamar
Nice Paul,
That is what you need. A lot of time in taxi. I bet it felt great!!!
If the cooling system does not cool well on the ground, it wont work in
flight. Forget about the idea that things will get better when we start
moving forward... they wont. Temps on the ground will be cooler than temps
on climb out, and about the same as temps in level flight.
-- David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
I expected the strong cross wind to have more of an effect.
The tail weight is quite heavy. I have not weighed it yet
but my guess is well over 100 pounds without me in it.
It is about all I can do to lift it off the hangar floor.
And that is with only 5 gallons per side.
If there is no slack in the cables the direction it points
is strictly a function of the rudder pedal/tail wheel position.
It was too hot to close the canopy and too windy with it open.
I need one of those WW I helmets with the flat plate goggles. :)
It is a bear to get it in and out of the hangar by myself.
There is a lot of load on the engine hoist casters so they
don't move very easily. The taxi way slopes up to the hangar
floor which is flat and horizontal. That means I have to push it
slightly up hill. I am thinking of shimming those steel channel rails so
they slope down instead of up. That way gravity will automatically
insert the airplane in the hangar :)
Paul Lamar
I bought one of the cheapest power winches from harbor freight, and fixed
it to the floor at the back of my hangar with anchor bolts, added a lnger
extension to the pushbutton control so it would reach to about 10 feet in
front of the hangar. Powered it from the battery charger. Pulled the plane
straight in over ice and snow.
C. Smith
Good idea. I'll take a look at what the have.
Paul Lamar
Paul,
What is the weight of the RV-4 and where is your center of gravity? I
thiink my tailwheel is around 50 lbs. I noticed your batteries are in the
back, but your radiators are under the engine.
You have done a weight and balance,right?
Brian Trubee
No weight and balance yet.
I'll take the bath room scale with me today and let you know
what the tail weighs. As I recall Mike said it was over weight.
The carbon fiber cowl is twice thick as it needs to be.
It is downright bullet proof. The big aluminum spinner is also
rather heavy.
Paul Lamar
Hey Paul,
I got my flywheel back from the machinist... it was pretty steep, costing
$350 including putting the starter in a lathe and taking down the flange,
taking down the addaper plate (both to make the starter reach the ring
gear), take down the clutch surface, drill and spot face the holes in the
flywheel.
Then today I went and had it re-balanced, $35.
Other costs included new bolts for the fly wheel (it is thicker) Aircraft
Spruce, $10 shipped. And the flywheel itself, $225.
Then there will be the new silicone bushings, but that is not properly part
of the cost of the conversion, which totals $620.
Tracy mailed my gears back to me on Monday, so they should be here any
second. The only other thing I need is the new bushings, and I should be
ready to get it all back together and flying..
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
OK Jim and I will make them tomorrow. The tools are done.
Looks like my way is cheaper :) Especially if we get an order
for half a dozen. Then I can get the 4130 disk water jet cut.
No starters mods required.
I'll be building a prototype this winter and selling Mikes
current gear box.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.