Subject: One way and centrifugal clutches
From: Rotary Engine
Date: 8/15/2011, 12:33 PM
To: AAA Put this in the To box


  After reading about all the failures related to the damper, I started
  to research into the subject of torsional resonance and found this
  article on how they have solved their problem on Bede 5. The original
  PDF is rather long so I just copy part of it for you to take a quick
  look. You can find the original file here
  http://ibis.experimentals.de/downloads/torsionalvibration.pdf

  The part that I think is of most interest is reproduced here:
  "THE FREEWHEEL CLUTCH
  The idea for a freewheel clutch came from our machinist, Ray Johnson,
  and I must give him the credit. He came in one day and told me that
  when he was a kid, his dad had a thrashing machine on the farm They
  would run the belt from the tractor to the thrashing machine and it
  had a freewheel device on it so that any vibration coming from the old
  two cylinder John Deere would be somehow taken care of. The minute he
  said "freewheel clutch", it rang a bell. After previously seeing the
  oscillating torque reversals of the prop I knew we needed some way to
  allow a torque reverse to occur without the bounce back. I had been
  looking at centrifugal clutches, manual clutches, etc. that could be
  used to disengage and allow some slip. We even tried a test with a
  super loose belt with idler pulleys but the slop still wasn't enough.
  The torsional amplitude was just too great at the low system frequency
  we were dealing with.

  Immediately after Ray mentioned the freewheel clutch, I started
  investigating and found a Borg Warner clutch that was used in
  automatic transmissions It was a double cage, full phasing sprag
  clutch. The double cage caused all the little cams inside to engage
  precisely at the same time. I had previously had experience with
  freewheel roller type clutches at Avian but we had problems with the
  brinelling of the clutch races when one roller would engage before the
  others and momentarily take the full torque, causing eventual clutch
  failure. The double cage full phasing, sprag clutch solved this
  problem."

   From there, I wonder if Tracy's original design really works or not? I
  am not sure if enough on the subject of torsional resonance has been
  done. May be even a different approach is necessary?

  Also, from my readings, it seems that many people recommends more
  cylinders for smoother torque curve. In my simple mind, a smoother
  torque curve alleviates the problem. The 2 rotors have one firing
  every 180 degree, similar to a four stroke so torque curve is not
  smooth. (See information on EPI Inc. on this subject)  A 3 rotor is
  similar to an in-line 6 at 120 degrees so may be 20B is more
  suitable/reliable for aviation? A 4 motor would be even better. Many
  great airplanes in WWI are V12s and they would not have a lot less
  problem with torsional vibrations.

  I am not a mechanical engineer, so anyone out there please correct me
  as much as they can. I am not building yet, not even a license to fly.
  But sure hopes to find time to do it soon.

  Henry Nee

   Hi,  One way and centrifugal clutches can help if the system has a low
rpm resonance peak.  The drive is not connected or only 1/2 connected so
the build up of loads at resonance can not occur.  If you go through the
critical rpm only once on start up and shut down, clutches can work.  If
the critical rpm is in the operating range, they will most likely fail.
The NSI gearboxes used sprag clutches.   I have info on the effect of the
SGF coupling on the Porsche aircraft engine if anyone is interested.
Similar torque, rpm and  firing freq as a two rotor.  I have a Mercedes
SGF
and the part numbers do not match the SFG chart.  Matching dimensions may
identify oem units.  Since they are normally used behind the cars gearbox
and see first gear torque, a unit from a pretty small engined car would be
likely the right size.  Finding a retail source other than car parts
departments might be a challenge.  I'll do a little searching.

Murry

Torsionsschwing of the Porsche aircraft engine without the SGF at peak was
0.86 degrees @ 550 rpm, running at 2500-5000rpm,  0.2degrees.   With SGF
peak at 0.34 degrees,  300 rpm,  running at 1000-5000 rpm 0.08 degrees.

 It is almost always cheaper to buy something than to make it yourself.
Murry

Depends on the cost, reliability of supply, the cleverness of the low
cost design and a whole host of other factors :) Will the product you are designing around be available next month or a year from now? One of the additional factors is the development of new low cast low quantity manufacturing  technology such as laser cutting.


Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.