Subject: One way and centrifugal clutches
From: Rotary Engine
Date: 8/15/2011, 2:46 PM
To: AAA Put this in the To box

 After reading about all the failures related to the damper, I started
 to research into the subject of torsional resonance and found this
 article on how they have solved their problem on Bede 5. The original
 PDF is rather long so I just copy part of it for you to take a quick
 look. You can find the original file here
 http://ibis.experimentals.de/downloads/torsionalvibration.pdf

 The part that I think is of most interest is reproduced here:
 "THE FREEWHEEL CLUTCH
 The idea for a freewheel clutch came from our machinist, Ray Johnson,
 and I must give him the credit. He came in one day and told me that
 when he was a kid, his dad had a thrashing machine on the farm They
 would run the belt from the tractor to the thrashing machine and it
 had a freewheel device on it so that any vibration coming from the old
 two cylinder John Deere would be somehow taken care of. The minute he
 said "freewheel clutch", it rang a bell. After previously seeing the
 oscillating torque reversals of the prop I knew we needed some way to
 allow a torque reverse to occur without the bounce back. I had been
 looking at centrifugal clutches, manual clutches, etc. that could be
 used to disengage and allow some slip. We even tried a test with a
 super loose belt with idler pulleys but the slop still wasn't enough.
 The torsional amplitude was just too great at the low system frequency
 we were dealing with.

 Immediately after Ray mentioned the freewheel clutch, I started
 investigating and found a Borg Warner clutch that was used in
 automatic transmissions It was a double cage, full phasing sprag
 clutch. The double cage caused all the little cams inside to engage
 precisely at the same time. I had previously had experience with
 freewheel roller type clutches at Avian but we had problems with the
 brinelling of the clutch races when one roller would engage before the
 others and momentarily take the full torque, causing eventual clutch
 failure. The double cage full phasing, sprag clutch solved this
 problem."

  From there, I wonder if Tracy's original design really works or not? I
 am not sure if enough on the subject of torsional resonance has been
 done. May be even a different approach is necessary?

 Also, from my readings, it seems that many people recommends more
 cylinders for smoother torque curve. In my simple mind, a smoother
 torque curve alleviates the problem. The 2 rotors have one firing
 every 180 degree, similar to a four stroke so torque curve is not
 smooth. (See information on EPI Inc. on this subject)  A 3 rotor is
 similar to an in-line 6 at 120 degrees so may be 20B is more
 suitable/reliable for aviation? A 4 motor would be even better. Many
 great airplanes in WWI are V12s and they would not have a lot less
 problem with torsional vibrations.

 I am not a mechanical engineer, so anyone out there please correct me
 as much as they can. I am not building yet, not even a license to fly.
 But sure hopes to find time to do it soon.

 Henry Nee

  Hi,  One way and centrifugal clutches can help if the system has a low
rpm resonance peak.  The drive is not connected or only 1/2 connected so
the build up of loads at resonance can not occur.  If you go through the
critical rpm only once on start up and shut down, clutches can work.  If
the critical rpm is in the operating range, they will most likely fail.
The NSI gearboxes used sprag clutches.   I have info on the effect of the
SGF coupling on the Porsche aircraft engine if anyone is interested.
Similar torque, rpm and  firing freq as a two rotor.  I have a Mercedes SGF
and the part numbers do not match the SFG chart.  Matching dimensions may
identify oem units.  Since they are normally used behind the cars gearbox
and see first gear torque, a unit from a pretty small engined car would be
likely the right size.  Finding a retail source other than car parts
departments might be a challenge.  I'll do a little searching.

Murry


Decades ago you could get a manual transmission car with overdrive
accessory .... and it had a one way clutch that might be
applicable.  The older SAABs with the 2 cycle engine also had one way
clutches in the transmission to prevent car momentum from spinning
the engine on overrun since there was little to no lubrication to the
engine if the throttle was closed.  Either of these parts might be used.

SD



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.