Subject: Off airport landing
From: Rotary Engine
Date: 8/16/2011, 7:51 AM
To: AAA Put this in the To box


    Hi, my chapter pres sent me this:

  NTSB Identification: ERA11LA444
  14 CFR Part 91: General Aviation
  Accident occurred Sunday, August 07, 2011 in Paducah, KY
  Aircraft: HODGES SAMUEL J RV-7A, registration: N462WP
  Injuries: 1 Minor,1 Uninjured.

  This is preliminary information, subject to change, and may contain
  errors.
  Any errors in this report will be corrected when the final report has
 been
  completed.

  On August 7, 2011, at 1340 central daylight time, an experimental
  amateur-built RV-7A, N462WP, was substantially damaged during a forced
  landing after takeoff from Western Kentucky Airpark (5KY3), Paducah,
  Kentucky. The certificated private pilot/owner/builder was not injured
 and
  the passenger incurred minor injuries. Visual meteorological conditions
  prevailed, and no flight plan was filed for the local personal flight,
  which was conducted under the provisions of 14 Code of Federal
 Regulations
  Part 91.

  According to the pilot, the airplane was equipped with an automotive
  conversion Mazda 13B rotary engine. After an uneventful preflight
  inspection, the pilot taxied the airplane and conducted a pre-takeoff
  run-up of the engine. During the run-up the pilot tested the dual
 ignition
  system and the primary and secondary engine control computers for proper
  function. Noting no abnormalities, the pilot proceeded with the takeoff.

  While climbing the airplane at an airspeed of about 100 knots, and about
  200 to 300 feet above the ground, the pilot noted that the engine began
 to
  "stumble" and lost partial power. The pilot responded by switching engine
  control computers, enriching the mixture, and then began searching for a
  forced landing site. He did not note any abnormal engine instrument
  indications, and could not recall the engine's rpm during the descent.
  During the forced landing to a nearby road, the airplane struck a mailbox
  and a ditch, damaging the left wing tip and the right wing spar.

  After the airplane was recovered to the pilot's hangar, the pilot and a
  Federal Aviation Administration inspector conducted a test run of the
  airplane's engine on the day following the accident flight. According to
  the inspector, the engine started immediately and exhibited smooth and
  continuous operation at an idle power setting.


  Not much of a clue as to what happened.

  I have had a reply from a distributor; may have SGF price and
 availability
  soon.

  Murry


  Ed, have you heard anything about this on the grape vine?

  Paul Lamar


 Yes, Paul

 Sam's engine started sputtering approx 200 ft altitude after take off.  He
 switched to controller B but no effect.  Engine continued to run but
 sputtering - .producing no useful power.  Landed on a dirt road
 encountering
 mail box and fence - no one seriously injured.  One wing totaled, the
 other
 repairable, fuselage OK.

 Engine ran fine back at the hangar with FAA inspector observing  - best
 guess (and that is all it is at this point) is he may have had "vapor
 lock"
 fuel problems.  OAT was 98F and he had been running up the engine prior to
 take off.  He does have return to tank fuel system which normally is
 pretty
 effective in preventing "vapor lock" - so it possibly has another cause -
 as
 yet undetermined.   He is also checking to make certain it was not muffler
 blockage as well.

 That's about all we know at this point.

 Ed

 Thanks Ed, Got any info on how and where Sam's fuel pumps were installed?
 I assume they were Walbro from Tracy. Is it possible he had water in the
 fuel?

 Here is what I did to Mike's RV4 pumps. Seems to work on the ground.
 I have yet to fly it as I am still trying to get an RV tail dragger check
 out to  satisfy my insurance company.

 Paul Lamar

Sams' pump and filters are located on the floor just in front of his
spar/selector switch location.  Looks like the same type of pumps Tracy
sells.  I've asked him whether this might be right above his muffler
location or not.

Having the pump near the tanks as shown in your photo looks like a smart way
to go - keeps high pressure in the part of the line that is most likely to
soak up heat.  I presume the black  box is a valve to control which tank the
fuel returns to?

Ed

Yes that is Mikes idea I think. Each tank has it's own pump. The tank selector switch also changes the electrically controlled switch selecting the return
tank. Very clever on the part of Mike if he thought of it.  Here is what the instrument switch panel looks like. Sorry about the picture quality. I need to
take a dedicated picture of just the switches. The green paint chosen does not give good contrast.


Good point about the muffler. Mike's right tank pump is just over the exhaust.
I'll have to run it up and put my hand down there with the floor board off.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.