Subject: Cell phone spy antenna
From: Rotary Engine
Date: 8/19/2011, 8:56 PM
To: AAA Put this in the To box


  I can record your conversations.

  Fully streamlined as it is inside the canopy.
  No gnd plane required because it is a dipole.
  The 1/2 inch T6 aluminum tube is clamped to the
  canopy cross brace so it moves (tilts) with the canopy
  and contains the coax feed cable. Holds the heavy balun
  in place no matter what.

  We shall see how well this works.

  Paul Lamar

  Hi Paul;

  My take on your new VOR antenna is: It will probably work well for signal
  from the front, Probably not quite so well with signal from the rear
  because
  of all the metal back there and very poorly for signal from the sides. The
  elements being tipped down dipoles, there is usually very little if any
  received energy on the ends of dipole elements and when they are tipped
  down
  they are cross polarized to the signal.
  What type of balun is used? If it is a Ferrite transformer they are pretty
  lossy also.  All of my antennas except the Transponder use what is called a
  Gamma Match so they don't need a balun. I will attach a paper explaining
  it.
  My Transponder antenna uses a tapered balun which is efficent also.

  Would you like me to send you one of my wing tip VOR antennas. Maybe I
  could
  bring it to you. I am based at Compton, used to be at Torrance but they
  threw me out of my hangar to build the Helicopter factory.

  Regards

  Bob

  Its from AC Spruce and here is what they say about it.

  "ADVANCED AIRCRAFT ELECTRONICS HIGH GAIN ANTENNA SYSTEMS

  Here is a new series of aircraft antennas specifically designed to be used
  without a ground plane. This means that composite aircraft and fabric
  covered aircraft can now have their antennas mounted totally within the
  structure. These antennas are designed using the latest engineering
  technology."



http://www.aircraftspruce.com/**menus/av/antenna_composite.**html<http://www.aircraftspruce.com/menus/av/antenna_composite.html

  I know nothing about the balun as it is potted.

  If it works some what in the receiving mode I'll get a VSWR meter and
  check it.

  I am attempting to use it as a com antenna. If it does not work I will give
  up and put a conventional com antenna on the bottom skin between the gear.

  Thanks for your thoughts.

  Paul Lamar

 Paul,
 I have one of Bob's VOR antenna's in my wing-tip and it works well.  I did
 with a whip com underneath for better vertical polarity and open sky in 360
 deg.   That being said, you could install a whip, then remove it and use
 your home made version for racing where the transmission distance is
 short.   Might be just what I need for Reno. :-)

 --
 David Leonard

 Turbo Rotary RV-6 N4VY
 http://N4VY.RotaryRoster.net
 http://RotaryRoster.net

 VOR's are horizontally polarized so they work well in wing tips.
 Com's are vertically polarized so they need to be mostly vertical.

 I am putting the word "Experimental" back in EAA here so I am staying
 on the bleeding edge for now :)

 If I need to I can borrow a whip out of the 182.

 Paul Lamar

Cut the top of your RV fin off, and remake it in the Rutan/EZ moldless
method..  You'll have to use a folded design, but it'll fit, and you
won't add any drag.


Matt-

I tested it today.
It works great where it is. It exceeded my expectations as did the FlightLine radio.
About ten times better than the C182 radios but that is not saying much.

In the steel hanger with the balun about 5 inches under the 182 wing.
I could read everybody in the pattern loud and clear. Canopy open or closed.

VSWR check next.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.