Subject: response from Rexnord Fluid Couplings about application
From: Rotary Engine
Date: 8/26/2011, 10:32 PM
To: AAA Put this in the To box


I emailed Rexnord rep to see if he had any fluid coupling ideas
for   me...guess not...

   Begin forwarded message:

   From: Brian Clark <Brian.Clark@rexnord.com
   Date: August 24, 2011 2:14:57 PM CDT
   To: gene kahn
   Subject: RE: question about fluid coupling

   Gene, spoke with some engineers about your application, the HP is
no   problem, but   the max speed for a fluid coupling is 1800 rpm.
 If you are looking for soft/start flexibility you might want to
look at a inverter for the motor.   Thanks   Brian Clark

   Brian,

   I am investigating the use of fluid couplings for applications
   of up to 600 HP, at 6-8 thousand rpm.  The diameter could
   be up to 14 inches or so, and the length [the thinner the
   better] could be up to 6 to 8 inches.  Do you have anything
   like that?  Thanks.

   Gene Kahn

   If one reads the article on the Fluidamper harmonic balancer that
someone   put on this cite, it says the silicon in it never wears
out and heat   doesn't   bother it.  It will turn to several
thousand rpm.  Seems like the silicon   is   coupling one piece of
metal to another to allow minute rotatational   reversals.  Hope
someone can use engineering voodoo to make something like   that work.

   Van

   Hi, there are such couplings used in some all wheel drive cars/trucks.

   Murry

  Hi all,

  Paul has mentioned that fluidamper type dampers have so far been
  designed for "crankshaft" type applications.  I took that to mean lower
  frequency range, stronger torque pulses and probably larger amplitude
  torsional twisting of the crankshafts.  The Fluidamper article
  says that they have designed their product specifically for DIESEL
  engines, which we know operate at lower rpm range from piston
  gasoline engines, and could also exhibit different torque pulses
and  crankshaft twisting depending on the specific design.

  All I was thinking is that the basic idea behind the fluidamper
might be  adapted somehow for our uses...for smaller, more frequent torque
  pulses etc.  Perhaps a stock fluidamper could be drilled and
lightened,  or different fluid could be substituted, etc etc.  If
not, there is so much  talent on this newsletter we could possibly
design our own from  scratch.  Even if we have to buy a new
fluidamper, cut it open to see  how it is made, it could be done.

  Paul tells us that our big problem is with "gear chatter".  I do
not know  if the primary source of gear chatter is intrinsic to the
gears themselves,  or if they chatter a lot more with whatever
torsional vibrations come from  the rotary itself [probably both].
 If some come from the rotary itself,  perhaps those could be
largely attenuated by some adaptation of the  fluidamper or
whatever.  If some gear chatter is intrinsic to the gearbox  itself,
then that might have to have its own separate solution...immersing
 the gears in viscous oil to simply damp the vibrations, or perhaps
by  changing the moments of  inertia of the gears through addition
or sub-  traction of weight in gear(s), or changing the materials
out of which  one or more of the gears are made ($$) thereby
altering the torsional  coefficient and affecting the primary
frequencies of vibration etc.

  I also was thinking that we have not actually tried Paul's new design
  damper/flexplate.  Heck, the stock flexplate sort of works, but develops
  cracks over time.  Could be worse.  And we don't have much time using
  the aftermarket flexplate.  I thought the idea of using larger
  rubber bushings was good, and Paul's redesign great.  If heat dissipation
  is a big issue for the rubber pieces, perhaps a housing could be
  designed allowing an oil spray to be directed onto the rubber bushings
  and collected for circulation through a heat exchanger.

  Just food for thought, I hope.

  Gene Kahn

I have total confidence in the engineers on this cite that they will
figure out a way to use fluid/viscous couplings if it is even
remotely possible.  Just seems to me that if silicon is impervious
to heat and wear (as per Fluidamper ad), then silicon sure is worth
pursuing as the coupling agent.  Only question is, why is it limited
to 1800 RPM.  If you could just build a BIG fluidamper type PSRU
(forget about the harmonic balancing aspect and just use the design
aspect) filled with a very stiff silicon so that there wasn't any
slip but only allow micro rotational reverses (like the rubber in
the current damper/flexplate allows) it would work????  But, I don't
know if I'm all wet.

Van


Gene,   Fluidamper also sells a line of automotive torsional dampers for
racing and another for street, as well as the heavy duty engines dampers.
These are designed for specific applications due the the specific torsional
demands of a particular engine. The diameters, inertia ring mass, the
clearances and I think the fluid are tweeked to remove the torsion at design
RPM range.

All wheel drive vehicles have a different system like a limited slip
differential, but the silicone fill lubricant causes them to lock up more as
the speed difference increases. Not quite what I see as needed.
RE the fan clutches, Dodge Diesels also use this drive system

Van,    the Rexnord couplings are designed for industrial applications which
is what will limit their RPM capacity. I have had to remove and install
numerous Fluidampers on heavy duty engines. Some of the Detroit Diesel 16V
engines use two on the front of the crank. They build these using what starts
as two 8V blocks but are machined differently so are really 16V blocks. One is
the front and the other the back. They also build a 20V with a 8V in the
center and a 6V on each end. Anyway, these engines run to 2100RPM in
continuous operation limited by the internals. The race 6V engines are
modified to run to 3600RPM with the stock damper. Injectors to 220mm cubed
instead of stock 90mm units. Lots of cancer causing smoke like the pullers.
These dampers would not be easy if at all possible to modify.

As regarding gear box chatter, search Lycoming redrive early failures. They
found light throttle on approaches was causing chatter and early failure. To
improve gear box life the pilots were trained to load the gear box; either
with power to take off or cruise, or closed throttle for landing.

Dale Davies

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.