I emailed Rexnord rep to see if he had any fluid coupling ideas for
me...guess not...
Begin forwarded message:
From: Brian Clark <
Brian.Clark@rexnord.com
Date: August 24, 2011 2:14:57 PM CDT
To: gene kahn
Subject: RE: question about fluid coupling
Gene, spoke with some engineers about your application, the HP is no
problem, but
the max speed for a fluid coupling is 1800 rpm.
If you are looking for soft/start flexibility you might want to
look at a inverter for the motor.
Thanks
Brian Clark
Brian,
I am investigating the use of fluid couplings for applications
of up to 600 HP, at 6-8 thousand rpm. The diameter could
be up to 14 inches or so, and the length [the thinner the
better] could be up to 6 to 8 inches. Do you have anything
like that? Thanks.
Gene Kahn
If one reads the article on the Fluidamper harmonic balancer that someone
put on this cite, it says the silicon in it never wears out and heat
doesn't
bother it. It will turn to several thousand rpm. Seems like the silicon
is
coupling one piece of metal to another to allow minute rotatational
reversals. Hope someone can use engineering voodoo to make something
like
that work.
Van
Hi, there are such couplings used in some all wheel drive cars/trucks.
Murry
Hi all,
Paul has mentioned that fluidamper type dampers have so far been
designed for "crankshaft" type applications. I took that to mean lower
frequency range, stronger torque pulses and probably larger amplitude
torsional twisting of the crankshafts. The Fluidamper article
says that they have designed their product specifically for DIESEL
engines, which we know operate at lower rpm range from piston
gasoline engines, and could also exhibit different torque pulses and
crankshaft twisting depending on the specific design.
All I was thinking is that the basic idea behind the fluidamper might be
adapted somehow for our uses...for smaller, more frequent torque
pulses etc. Perhaps a stock fluidamper could be drilled and lightened,
or different fluid could be substituted, etc etc. If not, there is so
much
talent on this newsletter we could possibly design our own from
scratch. Even if we have to buy a new fluidamper, cut it open to see
how it is made, it could be done.
Paul tells us that our big problem is with "gear chatter". I do not know
if the primary source of gear chatter is intrinsic to the gears
themselves,
or if they chatter a lot more with whatever torsional vibrations come from
the rotary itself [probably both]. If some come from the rotary itself,
perhaps those could be largely attenuated by some adaptation of the
fluidamper or whatever. If some gear chatter is intrinsic to the gearbox
itself, then that might have to have its own separate solution...immersing
the gears in viscous oil to simply damp the vibrations, or perhaps by
changing the moments of inertia of the gears through addition or sub-
traction of weight in gear(s), or changing the materials out of which
one or more of the gears are made ($$) thereby altering the torsional
coefficient and affecting the primary frequencies of vibration etc.
I also was thinking that we have not actually tried Paul's new design
damper/flexplate. Heck, the stock flexplate sort of works, but develops
cracks over time. Could be worse. And we don't have much time using
the aftermarket flexplate. I thought the idea of using larger
rubber bushings was good, and Paul's redesign great. If heat dissipation
is a big issue for the rubber pieces, perhaps a housing could be
designed allowing an oil spray to be directed onto the rubber bushings
and collected for circulation through a heat exchanger.
Just food for thought, I hope.
Gene Kahn
Mazda , had a fluid type design for its clutched radiator fan.
I know this isnt a viable option for an aircraft fluid coupling.
(well maybe for a large model airplane)
But they are sure effective, judging by the noise the create doing
their job, and probably a good design that would be easy to break
open and see how it works. They have a cooling fins on the front
center section, so I assume the fluid needs to be kept reasonably
cool. Probably necessary for any FC doing an amount of work.
I know these fans will loose their viscosity and break down.
Sam Watson
I have a few of those lying around. Maybe I'll take one apart and take
a look. It might work for our application.
Paul Lamar
Hey Paul,
Those fluid clutches on the cooling fan drive have fins on the front
because they need to sense the temperature of the air coming through the
radiator. The hotter they get the tighter they lock up. When the air
coming through the radiator is cool, I.E. the engine does not need
additional cooling, the fan runs free on the clutch. Same thing tends
to happen at highway speed. The natural draft is usually more than
enough to provide the required cooling so the fan is not needed.
I had a car where the fan clutch stopped working. No matter how hot the
engine got the fan would remain free on the clutch. I could reach in
and stop the fan with my hand. Took a bit of courage to try it. ;-)
I drilled a hole straight through the case and the clutch wheel and
stuck a bolt through it. That fixed the problem at the cost of a little
bit of fuel efficiency. Still cheaper than buying a new clutch.
- Mark LaPierre
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.