Subject: What is polar moment of inertia?
From: Rotary Engine
Date: 8/28/2011, 9:01 PM
To: AAA Put this in the To box


Why is it important when dealing with flex plates?

   http://en.wikipedia.org/wiki/Moment_of_inertia

   "In classical mechanics, moment of inertia, also called mass
moment   of inertia, rotational inertia, polar moment of inertia of
mass, or   the angular mass, (SI units kg·m²) is a measure of an object's
   resistance to changes to its rotation. It is the inertia of a
   rotating body with respect to its rotation."

   Also read gyroscopic forces.
   http://www.gyroscopes.org/behaviour.asp

   "When the gyroscope is spinning it can contain large amounts of
   stored energy. Newton's first law of motion states that any body
   will continue in its state of motion (still or traveling) until
   outside forces change it. Because of the forces when the gyroscope
   is spinning, if it is moved the gyroscope will try to 'compensate'
   for this movement. If we take the example of a gyroscope's axle
   being clamped to the structure of the car (often the cars engine
   behaves as a gyroscope because of its shape, mass and rotations)."

   "If the gyroscope/engine is spinning at a fairly high speed in a clockwise
   direction, as seen from the back of the car and as shown in the diagram
   above. When the car is turned to the right (clockwise from above)
   forces A and B are applied to the structure of the car forcing the
   front end of the car down and the back end up. If the car is
turned   to the left then the front end of the car is forced up and
the back   end forced down. If the gyroscope is spinning in the opposite
   direction then the reverse will happen."

   "However if the car was moved directly upwards, downwards,
 forwards,   back-wards or side-to-side the gyroscope would not
apply any extra forces.   The gyroscope only applies extra forces
when the car is moved at an  angle

   (turning left/right or when the front/back of the car is moved
   up/down). This effect is known as gyroscopic precession."

   These forces go through the flex plate out to the ring gear
  stressing the flex plate back  and fourth near it's hub thousands
of  times per minute. In other words the ring gear attempts to continue
  to rotate in it's original plain while the hub is being forced to
  change direction.

   Paul Lamar

   I agree that there is gyroscopic forces that affect the rotation
of  the flex plate. Also included with that is the toque converter which
  has a much greater mass. Any movement that would take place is held
  in check by the index hub on the converter  that goes into the back
  of the e-shaft or crankshaft and the bearing in the transmission
  pump. I am not sure the clearance of the bearing, but 0.002" seems
  reasonable. That would imply 0.001 movement which would be minimal
  flex in the flex plate. I am inclined to think the failures are due
  to the torque pulses applied to the flex plate under high
continuous  power loading. I believe you are right with the idea to
make a flat  disc of water jet cut stainless and tack weld the ring
gear on.  Lightening holes around the outer diameter will not fail
in my  opinion. But then what do I know as a burnt out mechanic :-))).

  Dale Davies
  -

  Dale,

  I am lost with what you are trying to imply with the clearances.
But  my conclusion on the RD-!B failure comes from this lecture on line.
  As it is stated there, it is "VERY NOT-INTUITIVE". The part about
  gyroscopic forces starts about 14:20 into the video.
  http://www.youtube.com/watch?v=zLy0IQT8ssk

  I must say I tend to agree with Paul that Torsional Vibration is
not  the problem here, and Mazda Rotary does not seem to have a Torsional
  Vibration Problem as is typical in piston based engine. So the RD-
1B  failure should be mainly due to metal fatigue of the flex plate.

  One solution is to use a very stiff flywheel from a manual
  transmission instead of a flex plate/ring gear combination. If the
  flex plate is eliminated, the precession force is transferred to
the  shaft, onto the bearings, and eventually to the aircraft
through the  engine mount, but the solution is heavier than a flex
plate/ring gear  combination.

  I think that for normal flying, a flex plate/ring gear combination
is  sufficient. But for people with acrobatic in mind, a flywheel is
a  better choice.

  Henry Nee

  My point is that the flex plate by itself without being coupled to
the  transmission could flex from the gyroscopic forces. The torque
converter and  the bearing in the transmission prevent any movement
from taking place.  Without movement, there will be no fatigue from
the gyroscopic forces. I was  asking about this earlier and Paul
educated me that gyroscopic forces at Reno  will be minimal.
Aerobatic will impart more, but that is controlled and  dissipated
out through the bearing in the PSRU, mount and to the airframe.

  I now believe the fatigue is starting from the twice per rev
loading and  unloading with regard to the compression and subsequent
combustion. This is  applied at the center of the flex plate and
resisted close to the outside  diameter. The drive plate with
isolator rubbers are bolted closer to the OD,  where the resistance
to the rotation is applied. The holes near the e-shaft  mount bolts
are a weak link due to the reduced amount of metal to transmit the
 power pulses through. You do not need movement and flexing to
generate fatigue  in metal. Look at conn rods that break. If they
have not been subjected to  stress from over revving the engine, the
break started from a surface  imperfection that allowed loading and
unloading of the rod to crack from  fatigue. When you look at a part
that has been fatigued, the break looks like  it crystallized. When
a part is torn apart from some other failure such as  over rev, the
separation point looks different.

  Mark S has experienced a failed flex plate without the aerobatics,
so that  bit showed me it is not a direct cause of the manner the
plane is flown. It  must be a factor of design and the limits it was
designed for. The factory  designs the flex plate with a low duty
cycle in mind. 30Hp out of say 210Hp  available is light load. In a
flying plane the engine is working at max power  for 5 to 10 minutes
and the cruise at 60 to 75% possibly for hours. The flex  plate was
not designed for this.

  With this in mind, I think Paul's re engineering with a flat SS
plate of
  0.090 to 0.125 thickness will cure the problems. It does not seem
that Tracy's  isolators are a source of trouble, but a rethink on
them may also be in order  as Paul is proposing.

  It all comes down to weight and designing for the application.
Mazda is  concerned with weight in the cars as the builders of AC
are. It is the duty  cycle that Mazda did not have in mind. They did
not use these parts in the Le  Mans engine.

  Dale Davies

Just more food for thoughtbecause there is a lot of talent on this letter
I was also thinking the same thing, and I pictured a much smaller
diameter 'flex plate' that is engaged by a worm gear from the starter
motor mounted at a 'right angle' to its usual orientation.  But the problem
would be DISengaging it quickly enough when engine starts.  Perhaps
could use a sprague clutch for this smaller flex plate to accomplish
quick disengagement.  Hey, if this is our only remaining
problemmight be worthwhile investigating.

Gene Kahn

Don't forget KISS! The simplest and least expensive route in my opinion,
would be Paul's idea of a flat plate. All that is required is the spacer ring,
a flat disc of stainless that can be water jet cut, and a replacement ring
gear. Longer bolts for the flex plate and weld the ring gear on. A quick
balance and you are in business. Stock starter works. Tracy's drive does not
seem to give trouble so just drill the drive plate for the bolt pattern.
Simpler than kissing an easy girl:-))).

Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.