Subject: What is polar moment of inertia?
From: Rotary Engine
Date: 8/28/2011, 9:04 PM
To: AAA Put this in the To box


Why is it important when dealing with flex plates?

  http://en.wikipedia.org/wiki/Moment_of_inertia

  "In classical mechanics, moment of inertia, also called mass
moment of  inertia, rotational inertia, polar moment of inertia of
mass, or the angular  mass, (SI units kg·m²) is a measure of an
object's resistance to changes to  its rotation. It is the inertia
of a rotating body with respect to its  rotation."

  Also read gyroscopic forces.
  http://www.gyroscopes.org/behaviour.asp

  "When the gyroscope is spinning it can contain large amounts of stored
  energy. Newton's first law of motion states that any body will
continue in  its state of motion (still or traveling) until outside
forces change it.  Because of the forces when the gyroscope is
spinning, if it is moved the  gyroscope will try to 'compensate' for
this movement. If we take the example  of a gyroscope's axle being
clamped to the structure of the car (often the  cars engine behaves
as a gyroscope because of its shape, mass and  rotations)."

  "If the gyroscope/engine is spinning at a fairly high speed in a clockwise
  direction, as seen from the back of the car and as shown in the diagram
  above. When the car is turned to the right (clockwise from above)
 forces A  and B are applied to the structure of the car forcing the
front end of the  car down and the back end up. If the car is turned
to the left then the  front end of the car is forced up and the back
end forced down. If the  gyroscope is spinning in the opposite
direction then the reverse will  happen."

  "However if the car was moved directly upwards, downwards,
forwards,  back-wards or side-to-side the gyroscope would not apply
any extra forces.  The gyroscope only applies extra forces when the
car is moved at an angle
  (turning left/right or when the front/back of the car is moved
up/down).  This effect is known as gyroscopic precession."

  These forces go through the flex plate out to the ring gear stressing
  the flex plate back  and fourth near it's hub thousands of times
per minute.  In other words the ring gear attempts to continue to
rotate in it's original  plain while the hub is being forced to
change direction.

  Paul Lamar

It is interesting to note that most of us have a gut-feeling for the
nature of linear-momentum. Its value is calculated as the product
Mass x Velocity, which is quite logical. As the mass of an object
increases, so does its momentum (3 times the mass, 3 times the
momentum). The same is true with velocity (3 times the linear
velocity, 3 times the linear momentum.

But with angular momentum logic and gut-feelings often fail to
account for the implications of increased angular velocity [RPMs] on
the forces, the momentum, and the resulting gyroscopic forces.

Centripetal (ie centrifugal) Force depends on (Mass x
VelocitySquared)/radius.  Or if one is thinking in terms of RPM ...
Force = Mass x Radius X Square of (6.28 x Rate of Rotation).  The
relationship is not linear, and most people (like me) are linear
thinkers. The forces on your flex-plates and such go up with the square
of the rate of rotation. Three times the rate of rotation=9 times the
centripetal force.

With Angular Momentum we also have a non-linear relationship. Angular
momentum of any rotating solid is calculate by thinking of each
solid as an infinite collection of rotating points, with each point
having its own Angular Momentum calculated by Mass x Square of
Radius of Motion. Adding up all these infinite little Angular
Momentums requires using calculus or a computer ( or a formula for
regular solids derived using calculus).  Since my calculus is a
little rusty, I will just say that logic fails most of us here. For
any given rate of rotation, Angular Moment depends in some way upon
the square of the rotating object's radius.  Add the fact that as
Paul mentioned, the gyroscopic forces are exerted at 90 degrees to
the axis of rotation and 90 degrees to any disrupting rotation and
my brain goes fuzzy on me.

So if one wants to minimize gyroscopic stresses on a spinning wheel,
keep the radius small and the mass low.

But then there are trade-offs, because we want a large radius and large
mass if we desire inertia for the "flywheel-effect" in pulse-dampening.
There is no free-lunch I guess.

Robin

It seems to me we don't have an issue with Tracy's damper but with
the Mazda flex plate. The only function the flex plate serves for us
is as a mount for the ring gear for starting the engine. If this is
the case perhaps the tree to bark up would be investigating further
the concept of starter/generators and eliminate the starter, ring
gear and flex plate altogether.

John
(OK what did I miss ?)

Way too ambitious. Given up on by major companies.
The problem is it takes 3 HP to start an engine.
There are two ways to get HP. Use a large low RPM motor
with high torque or use a small high RPM motor with a gear box.
The second choice is embodied in the current starter.
The first choice results in a heavy motor with poor
power to weight ratio. Hybrid cars.

Paul Lamar

OK. Air start ?

John

(grasping at straws ?)

Air motors work more or less the same way.
Torque verses RPM.

What the Russian's do is introduce high pressure air into
the the piston engine and let the pistons do the work.
Might work in the rotary. Then of course you have to recharge
the air bottle.

Paul Lamar

Yes exactly, some commercial trucks have these starters. Heard them
a couple of times and they fire those big diesels up really really
fast, not like cranking the engine at all. I'm not sure how much air
they use but would guess the pressure would be around 130 psi.
They're probably 15 or so liter engines so around six times the
displacement of the 13B. Perhaps a fire extinguisher bottle or O2
would have enough volume for a couple of starts. A small belt driven
compressor for recharge. Perhaps Dale can add some insight.

John


The air starters are built like a turbine engine. There are a few rows of
angled blades the same as turbine stages with stator segments between to
straighten the air flow and redirect it into the next section. They run on the
truck air supply of 120PSI. You have to have an air tank to store the starter
air. You only have one or two chances to get it started before needing anair
line. The weight and size of the air tank and air compressor would be a
problem even if you built a small air motor. Trucks use them because theycan
be more reliable and less expensive than an electric starter especially in the
cold. The truck starters probably weigh 1/3 the weight of a rotary engine. If
you are walking by and do not expect the noise when the starter is engaged,
you might fill your shorts.

The starter system Paul mentioned is used on some large industrial engines
like Cooper Bessemer. They put 100PSI air into the intake manifold. As the
intake valve opens, the pressure forces the piston down causing the engine to
rotate. When it starts the air is simply shut off. A V16 Cooper is big enough
there is a walkway just under the intake manifold which you can walk under.
The intake is on the outside of the engine. An overhead crane is used to lift
the rocker shafts and valve covers in place. The turbos are about two feet in
diameter and the engine must be 25 feet or so long. 4500HP at 102RPM. An
Allison gas turbine that with gearbox to drive a generator is 8 feet longand
stands 4.5 feet high on its skid. Also makes 4500HP.

I heard about a marine engine that used a D8 Caterpillar engine as a starter
motor.

Dale Davies



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.