Subject: How to tune with ADI?
From: Rotary Engine
Date: 8/29/2011, 4:22 PM
To: AAA Put this in the To box


Ok,  So I have the new ADI system installed and working....  I think?

Some of you smart racing guys probably have experience with ADI.

Most of the instructions that come with tuning it are directed toward car
guys that have computers and knock sensors.  All they do is turn the system
on and the computer allows more advance because I is not sensing any knock.
The only real advise I have so for for me is that I should be running just
less than the amount of ADI that it takes to bog down the engine.  My
system
is a fixed flow so I don't have much choice but it seems to be about right.
If I use straight water (which I did for initial testing), the engine bogs
after about 10-15 seconds of ruining the ADI system.  But when I uses a
50/50 mix of water and denatured alcohol (too hard to find methanol around
here, but close enough) the engine does not bog.

So assuming my amount of ADI injected is about right, now I am supposed to
be able to lean to better power and advance the timing a little.  But how
much?  For the last testing flight I was using EGT for lack of a better
guide.  When the ADI comes on, my EGT drops by about 30 deg C, and there is
a hint of roughness to the engine.  I can then lean a little and the
roughness clears up.  For my test flight I leaned until my EFT came back up
to where I normally limit it (890 deg C).  But if I then add 5 more inches
of MAP, there is still a hint of roughness even at 890 deg and I get the
sense that it wants to be leaned a little more. But I am afraid to do
that...  We are talking 45" MAP and 7300 RPM here (185 KTS indicated
(Vne) and climbing at 500 fpm).

So here are my questions:
Is EGT a useful tool here, and does leaning to get the EGT back to 890 make
any sense?
Since Methanol will do such a good job at preventing detonation, is it safe
to lean further toward best power (peak EGT)? (note, that will be hard on
the turbo...  I need to remember to bring the spare one to Reno)
How much advance do you think i can add?  I was previously ruining 5 deg
ahead of Tracy's recommended initial set up.  Can't give a number because
the EC2 retards the timing with higher MAP's.  How much, I have not heard.
I can easily add one deg at a time using Ed's EFI monitor.  But without a
knock sensor am really in the blind.

Thoughts?

-- 
David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net


I have a knock sensor I can loan you if I could only find it. On the turbo
engine it screws into the center housing. It generates an audio sound you
can feed into
the music input of your intercom. I am sure that Mazdatrix has one.
You can get an amp from MSD. You need it now.

Paul Lamar


Dave,
Go to your local racing shop that supports late models, sprint cars or dirt
modified cars and they will either have or know where to get methanol.
It is
important to tune with it rather than water or denatured.

Install a water flow control valve in a place easy to access. This allows
easy tuning of the amount of adi flowing to control inlet air temp. Some of
the race mustangs using adi have the intercooler removed and the adi is
adjusted to maintain the inlet air temp based on the manifold pressure they
are running. An amount of de-enrichment still happens to run the engine at
best power, but not as much as the air cooled engines.

On the rotary we don't run them anywhere near as rich as the radial
engines,
so you won't be pulling out near as much fuel by percent. The biggest
safety
margins are gained with the reduction in inlet air temps.

Two simple tools will help you tune, an inlet air temp gage that is in the
line of sight, and a wide band O2 sensor in the exhaust. We don't use a
knock sensor, as the background noise level in the radials are so high, it
thinks everything is knocking.

ADI for inlet temperature control, and wideband for fuel mixture.
The addition of a water spray bar on the outside of the intercooler doesn't
hurt either, and water sprayed on the oil cooler will allow you to run less
air flow (less drag).
See you up at Reno,
Larry

The MSD knock sensors have a visual indication as well as audio.

Paul Lamar

I used to purchase Methanol from a local LPG/Petroleum distributor.
They use it in the propane tanks to minimize line freezing in winter.

roger



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.