Ok, So I have the new ADI system installed and working.... I think?
Some of you smart racing guys probably have experience with ADI.
Most of the instructions that come with tuning it are directed toward car
guys that have computers and knock sensors. All they do is turn the
system
on and the computer allows more advance because I is not sensing any
knock.
The only real advise I have so for for me is that I should be running just
less than the amount of ADI that it takes to bog down the engine. My
system
is a fixed flow so I don't have much choice but it seems to be about
right.
If I use straight water (which I did for initial testing), the engine bogs
after about 10-15 seconds of ruining the ADI system. But when I uses a
50/50 mix of water and denatured alcohol (too hard to find methanol around
here, but close enough) the engine does not bog.
So assuming my amount of ADI injected is about right, now I am supposed to
be able to lean to better power and advance the timing a little. But how
much? For the last testing flight I was using EGT for lack of a better
guide. When the ADI comes on, my EGT drops by about 30 deg C, and there
is
a hint of roughness to the engine. I can then lean a little and the
roughness clears up. For my test flight I leaned until my EFT came back
up
to where I normally limit it (890 deg C). But if I then add 5 more inches
of MAP, there is still a hint of roughness even at 890 deg and I get the
sense that it wants to be leaned a little more. But I am afraid to do
that... We are talking 45" MAP and 7300 RPM here (185 KTS indicated
(Vne) and climbing at 500 fpm).
So here are my questions:
Is EGT a useful tool here, and does leaning to get the EGT back to 890
make
any sense?
Since Methanol will do such a good job at preventing detonation, is it
safe
to lean further toward best power (peak EGT)? (note, that will be hard on
the turbo... I need to remember to bring the spare one to Reno)
How much advance do you think i can add? I was previously ruining 5 deg
ahead of Tracy's recommended initial set up. Can't give a number because
the EC2 retards the timing with higher MAP's. How much, I have not heard.
I can easily add one deg at a time using Ed's EFI monitor. But without a
knock sensor am really in the blind.
Thoughts?
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
I have a knock sensor I can loan you if I could only find it. On the turbo
engine it screws into the center housing. It generates an audio sound you
can feed into
the music input of your intercom. I am sure that Mazdatrix has one.
You can get an amp from MSD. You need it now.
Paul Lamar
Dave,
Go to your local racing shop that supports late models, sprint cars or
dirt
modified cars and they will either have or know where to get methanol. It
is
important to tune with it rather than water or denatured.
Install a water flow control valve in a place easy to access. This allows
easy tuning of the amount of adi flowing to control inlet air temp. Some
of
the race mustangs using adi have the intercooler removed and the adi is
adjusted to maintain the inlet air temp based on the manifold pressure
they
are running. An amount of de-enrichment still happens to run the engine at
best power, but not as much as the air cooled engines.
On the rotary we don't run them anywhere near as rich as the radial
engines,
so you won't be pulling out near as much fuel by percent. The biggest
safety
margins are gained with the reduction in inlet air temps.
Two simple tools will help you tune, an inlet air temp gage that is in the
line of sight, and a wide band O2 sensor in the exhaust. We don't use a
knock sensor, as the background noise level in the radials are so high, it
thinks everything is knocking.
ADI for inlet temperature control, and wideband for fuel mixture.
The addition of a water spray bar on the outside of the intercooler
doesn't
hurt either, and water sprayed on the oil cooler will allow you to run
less
air flow (less drag).
See you up at Reno,
Larry
The MSD knock sensors have a visual indication as well as audio.
Paul Lamar
Thanks for all the great advice and info Larry.
Tracy Crook mentioned that he tried to get a knock sensor to work with the
rotary, but the filter algorithm was just too difficult to produce. You
can't just use any filter, it has to be designed for the 13B.
Ed Anderson tried to add Wide Band O2 capabilities to his EFI monitor, but
realized that the sensor temp must be tightly controlled, and that
technology is difficult and expensive. And even if I had a WBO2, I still
would not know exactly what mixture I should be shooting for.
Right now, my manifold temp sensor is located in the plenum right next to
the ADI injector, so it is not reading temps down stream of the ADI. I
suppose I can move it or install another, but then I will need to know the
temperature goal that I am shooting for. And you say that varies with MAP?
All this is becoming too much of a project for what will likely be a
one-time event for my plane. If I plan to do any serious competition at
Reno in future years. I need: a new airframe with less drag and a higher
Vne (most likely dedicated to racing), a 3 or 4 rotor, more time, and more
money :-)
So for this year, my thinking is thus: During PRS, I ran 217mph, which,
would likely put me at a distant last in the sport class. Even with
unlimited power, my airframe still limits me to somewhere around 230-235
mph. And that is merely a not-so-distant last place.
Now, I ran 42"MAP for PRS without any kind of ADI. Now that I have ADI of
some sort, I should be able to run, say, up to 48" or so without getting
into detonation. Wouldn't you say? There are other restrictions as well,
along about 45" and 7500 RPM my RPM gauges go blank saying I am maxing out
my injector duty cycle - so I could use some bigger injectors. That also
seem to be pretty close to maxing out my turbo at that altitude, unless I
disable the waste gate actuator for race week.
I really hear what you say about spray bars and closing down the air inlets,
but again, too much work for a one-off race week.
So given all that, do you thing there is any info to be gleaned from EGT?
See you there!
--
David Leonard
Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net
I am thinking of putting retractable gear on the RV4. I am sure I will get a
lot of static from Van if he hears about it. It is real easy to move the
stock fuel tank outboard and add a root strake to house the wheel. Much
like a P51. I will need to find a thiner wheel of some sort that will fit.
With Mike's skinny cowl it will look just like a P40. Van warns about
putting fuel in the outer wing panels as he is worried about increased the
polar moment of inertia about a vertical axis in a spin.
What he is not telling you is he failed to put a strake on the RV vertical
stabilizer like almost every other airplane in the world has includuing most
all Cessna's and the P51. When the aircraft is in a spin a strake generates
a powerful vortex and low pressure area on the down wind side of the strake
tending to retard the spin. That is easy to add to an RV as there is
already a fiberglass fairing back there.
I suspect a lot of RV'er would like to retrofit their RV's with retractable
mains.
Paul Lamar
Dave,
Trying to figure out what is going on using egt with adi will keep your head
down in the cockpit and not out on the course where it belongs.
The reason for more adi with added manifold pressure is the pressure pump
(turbo in your case) makes more heat with more boost. That is why I cannot
stress enough the use of the two gages. And the Commander wide band is easy
to use and does data logging. We are on our second year of flying with the
sensor installed using both leaded race fuel and 100LL and haven't killed
the sensor yet. Fuel mixture is a know.... 12.5 to 13 to 1 with ADI on (with
intake air temps under control) and 12 to 1 without (at full power). I would
even try running at 13.5 to 1 if the intake temps are good. In all the non
automatic systems require a lot of tuning coming down the chute as you want
them set when you enter the coarse (of course you have more time to twiddle
with things at only 220). I will be at Reno on the 9th through the 19th, so
look me up and I will give you a hand as time allows.
Larry
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.