Subject: centrifugal clutch and gear box chatter. SPINNING PROP DRAG
From: Rotary Engine
Date: 9/7/2011, 9:59 PM
To: AAA Put this in the To box

  When I first saw Bud Warren's centrifugal clutch something  in
  the back of mind was trying to tell me he did not build it.
  The parts looked too slick and too finished to be custom made.

  I think I figured it out. They are stock parts out of Center Force
  clutches. Of course Bud never talked about that.



  Ironically I have one in my my RX8. I love it. It works great.

  This will solve the gear box chatter problem if set up properly.

  The question is how thick must be the flywheel? That will
  affect the over all weight.

  BTW I don't think it was the cause of Bud's fatal crash.


  Paul Lamar


  Confusing pics though....  it seems you've got a few pics of
  subaru/eggenstein's --  did they use
  bud's drives?  William Mason

  Yes. He sold several.

  ------------------------------**------------------------------**--
  Center Force also make a compatible aluminum flywheel for the 13B.

  Paul Lamar


  There is another way to eliminate the gear chatter.  Throw the gear
  box
  out.  Mount an alternator on the eshaft,  a prop on a direct drive
  electric
  motor and all the drive line problems go away. Like a diesel electric
  locomotive. Any remaining problems can be handled in the software of the
  controller. The option of adding batteries would exist if you want to be
  way trendy.

  Murry I Rozansky

  As I said many times before on here electric drives of that type suck big
  time.  This is a recording :)

  The motor is 85% times the alternator is 85% the over all effciency is
  .85 times .85 = .72% over all. You are wasting 30% of your fuel.
  Locomotives do it for one reason and one reason only. High starting
  torque.

  Paul Lamar

  Hi Paul,  was meant to be a humorous.  If there are no torque reversals,
  it must be drive line resonance.  What else could it be? Has any one tried
  running with a solid shaft connection, no flexible element?  A soft enough
  coupling should work. A disconnect will of course and a Bud type is simple
  and compact enough to fit. If it does not cause operational or safety
  problems to idle the engine above the chatter speed, why is  gear chatter
  getting so much attention?  Some of the couplings have a surprising amount
  of wind up at their rated torque.  I think some were over 10 degrees.  If
  chatter at idle, when there are very low loads does not damage anything,
  maybe the problem is of a more psychological or esthetic nature.  Tracy's
  damper design just seems overly massive to me.



  Murry I Rozansky

  Tracy's rubber bushings are so stiff for all practical purposes it is
 locked
  up. I suspect there would be no difference. Same gear box chatter.
  It is not unique to the rotary either. That is why Bud attempted to deal
  with it.  You have this huge flywheel on the out put end of the gear box
  called a prop :) Could be caused by a combination of many things. Slop in
  the splines or gear back lash. You will never get away from some wear or
  slop.
  Molt Taylor was the first to deal with it by using a centrifugal coupling.
  It was noticed by Allison on the shaft drive P39 back in the 1930's.


  The down side would be prop wind milling which would increase the power
 off
  stall speed. In fact that could have killed Bud if he did not realize it.
 It
  was a low altitude stall spin crash. You must land faster with a wind
  milling prop. If you do a wing over to turn around the prop might stop.
 Then
  again if it did not stop you would lose a lot of altitude.

  ------------------------------**------------------------------**--

  This last chart shows for certain pitch ranges the wind milling prop is
 less
  drag than a fixed pitch prop. It may turn out to be that way if you have a
  fixed pitch cruise or top speed prop.

  I think one must test for this at altitude where is is possible to restart
  the engine or make the runway regardless.
  Since the prop must drive the gear box backwards wind milling may not
 occur
  using Tracy's gear box.

  Slipping is a similar high drag situation so by all means practice
 slipping
  on final. IMHO I would never try to make a conventional approach with a
 dead
  engine unless I was so far down wind and so low I had no other choice. In
 my
  opinion slipping is under rated.

  Paul Lamar


  Hi Paul

  Re the attachment of the spinning prop drag.

  I think this backs up what I was saying about, the loss of a Europa/NSI
 when
  the engine stopped the prop went into "free windmill" mode as the clutch
 was
  not powered the prop was just spinning free worst case scenario.

  That's exactly what the pilot reported, "like having a huge spinning drag
  brake"

  In a fixed prop mostly you have to dive a high speed to attempt an engine
  re-start.

  So most pilots would not appreciate the danger involved.

  The drag of a stopped prop isn't anything like the drag driving the prop
  plus the drag created by the prop spinning finds a point of equilibrium or
  the sum of those two drag amounts combined.

  Some of the lower cost wind generators work use tip stall drag to limit
 rpm
  in high wind. Ugly noisy but cheap.

  Any drive system(by accident or design) that could allow the prop to spin
  free potentially a KILLER.

  That's my understanding of the situation.

  Kind regards

  Clive

  One really needs to know what the pitch was to draw any conclusions.
  A windmilling prop can be lower drag under the right circumstances.

  Paul Lamar


 Peter Garrison recently did some tests on this, changing prop and throttle
 settings I believe..  Or at least talked about it.


 Matt-


 Peter, can I  have the publication date?

 Paul Lamar


Paul,

Here are the manuscripts of the two articles.

Peter

Thanks Peter. Very interesting.

I am going to have to study these and see if we can translate to
the rotary with the 2.85:1 gear box. We have some numbers on the
rotary friction as well. I suspect the pumping losses would vary
with throttle open or closed.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.