Subject: Gear box pictures
From: Rotary Engine
Date: 9/20/2011, 2:18 PM
To: AAA Put this in the To box


 Hello Paul,

     What a sad and disturbing weekend at Reno.  My thoughts to all
concerned.

     I scanned the RD-1C Assembly Manual and photographed the
   unassembled unit.   Tracy ships the unit with the prop shaft already
   assembled so I do not have  photos of the full unit sans housing
 as   Ed requested.  The material is in a  huge zip file folder (84
 MB) at   the following link:

     http://www.lexami.com/pdf files/rd-1c manual and photos.zip

     I hope this is useful.

     Let me know if you have trouble accessing the file.

     William Hagood

     Thanks William.

   The link did not open, perhaps its not strung together right.

   Ed Carver

   If you go to Real World Solutions site and read the PSRU development
 dissertation, it will inform a lot. Also look at the RD-1B and RD-1C
 topics. There are photos of both gear sets. I attach here the page
 from the 2006 FRPP catalog with the wide ratio sets for both the C6
 and AOD transmissions. I have circled the parts I think go together
 as shown in Tracy's photos. I used red and blue pencil to
 differentiate. Hope it shows up.

 Dale Davies

 The Ford Racing Performance Parts are likely to be higher priced than
 the stock parts. One can get 2.85:1 and 3.17:1 out of the stock parts.

 Here are a few illustrations.

 BTW it is always best to modify a successful and proven aircraft
 assembly rather than start from scratch. At least 100 Ford C6 based
 PSRU's have been flying with 1000's of accumulated hours for many
 years. We have learned what not and what to do. Invaluable R&D by
 the best test people available. The customer.

 Paul Lamar

Hi Paul,

 I was just watching the posts on the parts to get. The FRPP wide ratio
parts
are sourced from the 4R100 transmission. The two circled in blue look like
the
parts that would be in the 2.17 box, or reverse output. The red circled
parts
look to be the ones Tracy uses in the 2.85 box, or same rotation output.

Dale Davies


Paul,   I am not sure what you are implying with the stock bellhousings.
From the first picture it appears to be 5-7/8" high where Tracy's spacers
are 3" and the 20B automatic bellhousing appears deeper yet. Both would
require an adapter to the PSRU planetary drive making it taller yet. If we
put Jeffs plate  between the rear housing and bellhousing to mount the
engine that adds another 1/2" and a similar thickness spacer behind the
flexplate to get the ring gear at the right depth. An entirely new PSRU
might be shortened and designed to fit the manual bellhousing without an
adapter, however the propshaft bearings would be very close together since
the planetary gearset thickness is pretty much written in stone, and adding
hydraulic prop provisions would likely be impossible. The only upside to the
bellhousing would be useing the marine torsional dampers  which  are
available in several horsepower ratings.They are too tall to fit in the
space between the E-shaft and Tracy's box necessitating an increase in the
sidehousing to propshaft dimension.
        I have been following Ed Carver's investigation of the input shaft
parts. Aparently there is an OEM Ford part with the correct splines
available but would require a sleeve. If the shaft were slightly tapered
over the length of the sun gear and the inside of the sleeve had a
corresponding taper then it could be a press fit assembly not unlike the
e-shaft to counterweight flange. The  cross drilled bolt hole would
then function more like a safety wire. The sleeve would not be a hardened
part so it could expand into the sungear, or could be a split sleeve and
hardened.
           The 12 rotor marine rotary in an earlier post shows a side
exhaust and P-port intake arrangement. It wis also stated that the rotors
are "OEM" purchased on e-bay. It is normally aspirated without tuned length
intake runners or exhaust headers. That would seem to indicate approximately
1320HP. The pictures also show large cutouts on the sidehousings indicating
separate wear plates as you suggested and Rhichard Sohn uses in his one
rotor. The e-shafts are 3 piece and there are three of them geared together
at the drive end.

george grimes


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.