One other thing we are learning is apparently the engine
tension bolts are lengthening under high boost (over 45 inches
of Hg) and allowing some small amount of combustion gas leakage
into the cooling system. Mazdatrix among other are dealing
with it.
http://www.mazdatrix.com/studkit.htm
I am still looking for 12.5 MM (1/2 inch) titanium studs
to save the weight as 16 12.5 MM steel bolts are quite heavy.
The modulus of elasticity of titanium is about 16 million
while steel is 30 million.
The area of the stock 10 mm tension bolts is 78 mm
while the area of the 12.5 mm bolts/studs is 123.
That makes the 12.5 mm steel bolts/studs almost
twice as stiff.
So the 12.5 mm titanium studs do not appear to be stiffer
(due to the lower modulus of elasticity) than the stock
steel tension bolts. Only weight is saved over 12.5 mm
steel.
http://en.wikipedia.org/wiki/Young%27s_modulus
Another factor is pre load. If one can torque the tension
bolts higher that delays the expansion to a some what
higher boost level. How much I have not figured out
yet.
IMHO it is best to stick with 12.5 mm(1/2 inch) high strength steel.
Paul Lamar
Racing Beat suggests torque to 32 pounds for boosted engines. I torque to
the lowest end of the spec for a specific engine but I use Nickel
anti-seize compound on the clean threads and under the bolt heads. Have a
few spares
on hand as a couple may be ruined this way. Never a problem.
Lynn E. Hanover
There could be another cause of leaking O-rings and that is shrinkage of
the rotor housings due to over heating. The stock 13B water pump restricts
the rate of water flow through the engine. I have no idea what went through
the Mazda engineers mind when they did that. It was completely done away
with
when they came up with the RX8 water pump.
You want a high flow of water through the block to carry away the heat in
the metal.
Some people reduce the size of the lines going to and from the radiator
which is also bad idea. Some people grind groves in the water jacket around
the lower plug to enhance the heat transfer from the metal to the water.
This may be necessary with a high HP rotary turboed or other wise. I am not
sure yet at what HP level this becomes necessary.
Here is a trick to monitor the cooling system. Pressurize it with air before
a flight to see if it is leaking internally to the cap setting. Usually
about
30 psi. Watch the coolant system pressure gage when you do this. All of that
is covered in my book How to Cool Your Wankel.
Another trick is use one of these pressure gages to monitor what the cooling
system is doing after the engine is shut down. When the engine cools off
a vacuum is generated inside the engine that draws coolant back in from the
the
atmospheric over flow tank through the one way valve in the pressure cap.
If the coolant system is leaking internally from the combustion chamber to
the water jacket this vacuum reading will be reduced.
Also the pressure reading may be reduced as the engine is running if there
is internal leaking from the water jacket to the combustion chamber.
There could be a case where steam is being generated
so fast the pressure reading may remain high for a while. In any event you
will get a feeling for what is normal in a well sealed engine.
I learned this trick from Ken Welter whom had one in his Coot.
I am installing one of these in the RV4 as we speak.
Paul Lamar
I would probably use an all metal valve stem with a threaded
base/nut.. That rubber one in the pictures seems a bit cheesy..
Matt-
Standard tubeless tire valve.
They work for years on your car under much worse conditions.
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.