Subject: Possibe way to take out alcohol in fuel
From: Rotary Engine
Date: 9/26/2011, 12:59 PM
To: AAA Put this in the To box


snips...

On another note, I have located a new upper wing for my Glass Goose to
replace the one that was eaten up by the alcohol in ethanol gas. I'm going
to replace the wing and get 'er flying myself. I'm sure glad the Renesis
ran
like a top. It'll give me motivation to get it going again after I finish
a
SeaRey LSX.

Sandy McNabb
Renesis in a Glass Goose (on temporary hold)


Sandy, I understand that Briggs and Straton have an alcohol test kit
for auto gas.  Rumor has it high test auto gas in some areas does
not have alcohol.

Paul Lamar

I was talking with Rich Martin the other day and he spoke with a gas
tanker
truck driver who said
that as far as gas goes costco gas has the best additives. don't know if
they also add ethanol.
Might be worth a look.
Brian Trubee

-----------------------------

I just ordered a alcohol test kit from
http://www.fuel-testers.com/order.html  This was an subpage on a Briggs
and
Straton site.
Here are a couple of sites to locate non-alcohol gas.
http://www.buyrealgas.com/  and  http://pure-gas.org/
You can also sign a petition against Ethanol on the Briggs and Straton
site.

Hopefully, after the election the Republicans will can the ethanol fiasco.
It's costing us at the dinner table because of the increase corn prices to
feed livestock, not to mention the damage to our engines and hoses.

Sandy McNabb


Not a chance the Republicans will end these subsidies.. The corn
growers (and now the corn fermenters/distillers) now fund the right
people on both sides of the aisle to keep this going forever.


Cheers,

Matt-


Been reading this gasoline/alcohol thread, and it just occured to me,
that the way the test kit
works, also seem to be the key to take alcohol away from fuel.

It would be a fairly simple affair actually.

The test is based on the principle that alcohol and water mix,....
alcohol and gas mix,.... but
water and gas don't mix.

Plus, what will not mix...will stratify, into two different liquids, in
two layers with the most
dense on the bottom, the alcohol/water mix in the bottom, and gasoline on
top.

If there is alcohol in the fuel, you will se an even mix, but if you ad
water, the alcohol will now
leave the mix with gasoline and instead mix with the water.

The test is basically that you take 10 units of gas, and one unit of
water. There is a mark on the
test tube, where you fill it up exactly with water, then you fill up the
rest , to the next mark
with the gasoline you want to test,  shake it, and let it settle, once it
settle, the new stratified
liquid in the bottom, will be the water and alcohol mix, and depending on
how high up the
water/alcohol mix goes in the test tube, compared with when the level
that was pure water, it will
now determine how much alcohol there is in the fuel.

It just occured to me...you have just now removed the alcohol from the
fuel....and it is now
together with the water sitting in the bottom, ready to be drained, and
the rest on top , is fuel
without alcohol.

Would you have 10 gallons of fuel, ad one gallon of water, and stirr it
briskly for a minute or so,
and let it settle, (...I have seen in  the test...it stratifies very
quick,) you would get the same
thing,  drain out the water/alcohol mix in the bottom and it should be
alcohol free fuel.

Would'nt it ?

Roger

--  You could use  the drained water alcohol for ADI, water injection.


Murry I Rozansky


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.