Paul,

One more thing. Got the following from this link http://catb.org/gpsd/

"gpsd is a service daemon that monitors one or more GPSes or AIS
receivers attached to a host computer through serial or USB ports,
making all data on the location/course/velocity of the sensors
available to be queried on TCP port 2947 of the host computer. With
gpsd, multiple location-aware client applications (such as
navigational and wardriving software) can share access to receivers
without contention or loss of data. Also, gpsd responds to queries
with a format that is substantially easier to parse than the NMEA 0183
emitted by most GPSes. The gpsd distribution includes a linkable C
service library, a C++ wrapper class, and a Python module that
developers of gpsd-aware applications can use to encapsulate all
communication with gpsd."

Basically it reads data from a GPS Mouse (Actually an active GPS
Antenna with a serial interface) and outputs it to a serial port. gpsd
reads the serial data, (it finds the port of the gps mouse) and
re-exports it to TCP port 2947. Once exported to TCP port 2947, anyone
on the TCP/IP can connect to it and find the location of the GPS
Mouse. I am not sure that is what you want to do!

regards,

Henry



On Sun, Oct 9, 2011 at 10:28 AM, Henry Nee <hpc.nee@gmail.comwrote:
Paul,

I think NEMA calls for 4800 baund 8N1, (8 data bits, no parity, 1 stop
bit.) Did you set your terminal to communicate at that baud rate and
8N1 setting? Once connected, it should show data. Also, remove your
gpsd for now. It talks to the gps and present data to your application
if I am not mistaken. So it should not be there.

regards,

Henry


On Sat, Oct 8, 2011 at 11:01 AM, Rotary Engine <rotaryeng@earthlink.netwrote:

Hi Henry,

I am making a bit of progress on reading the GPS.
It is on port ttyusb0 according to lsusb
Bus 008 Device 006: ID 1163:0200 DeLorme Publishing, Inc.


I found a gpsd daemon and installed it but I don't know how to get
it to send data to the Ubuntu 10 terminal or anywhere
else for that matter.

The system monitor does not tell me it is running.
The GPS is plugged in and blinking.

Any tips on that?

Paul Lamar

I about where you are in getting my GPS to talk to me.  Difference is
that my GPS doesnt blink at me, the red light is just steady.

I used the Ubuntu Synaptic Package Monitor and installed minicom.

On my computer the GPS plugged into usb port is usually recognized as
ttyusb0, but when the system locks up due to my fiddling around, and I
plug it in again, it will sometimes come up as ttyusb1, and once I even
saw ttyusb2 show up in the /dev directory. ???????

When I run minicom and tell it to communicate with the correct USB port,
it just sits there and listens; no data seems to be streaming from the
GPS.  I am wondering if there is some sort of a "go" command that the
GPS is looking for.

On another topic.  I just bumped into a neighbor a few minutes ago at
our local recycling center, and I mentioned my aircraft project.  He
says he has a 2004 RX8 engine in his garage that belongs to his buddy.
Says that he thinks the seals are bad. He wanst to get it out of his
garage.
What's it $worth?

R Berglund

What version of Ubuntu are you using Robin?
There are at least 2 formats in use. Most popular
is ASCII NEMA 0183. I think the other is binary.

Offer him $50 :)


Paul Lamar


Paul,

You may want to try this software:
http://www.visualgps.net/VisualGPS/default.htm

It is freeware, and should do the things you were thinking but needs a
Windows Mobile unit like a pocket PC instead of Android. Let me know
if you are thinking about doing the same thing in Android Tablet?

Henry

We don't really need if for the tablet as all the good ones have built in
GPS receivers. I just want them to work with Tracy's computer and latter
we can get this device to work as an EFIS. They do have some Linux source.

Works great on Windows XP USB and is real cheap at under $100.
http://www.hytekautomation.com/

"The iUSBDAQ - U120816 is the lowest cost USB data acquisition module which
provides eight 12-bit analog inputs, 16 digital I/O lines, two programmable
pulse-width output channels, and one 16-bit counter channel. Analog sampling
rate is up to 32 ksamples/s for all 8 channels, with single channel up to 13
ksamples/s."

I forgot about it when you were up here or I would have shown it to you.
This is the cheapest way to get an EFIS working on the tablet.
One can tell what Tracy is doing by monitoring the pulse width
on the injectors with an opto iso.


Paul Lamar

The Arduino Mega may be cheaper.  Found one yesterday for under $60 on Mouser.

Chris Cosman

I'll bet it is not 12 bit A to D :)

Paul Lamar