Subject: 3.17:1 gear box super simple PSRU]
From: Rotary Engine
Date: 11/3/2011, 11:08 PM
To: AAA Put this in the To box


Paul

are you sure you want to use 7075??
I have a great source for 7050 with certs cheap cheap cheap it's all
boeing scrap.
maore than you will ever use. My machine is not being used at the moment.
I can machine the plates and squares
if you send me the drawings.

Tony

I'll get back to you when I get back from check rides Tony.
What dwg format can you use. We might try a built in planet
carrier on the 4 inch aluminum shaft.

Perhaps Ed needs something right at the moment?

Paul Lamar


This picture will give you a feel for the strength and robustness
of this type of four inch diameter aluminum prop shaft  PSRU.


Paul Lamar


That looks like it otta handle it. The shafts on the 2.85 are 4.17", which
leaves me with perhaps a .020 wall thickness; if I edm for 3/8 bolts. I
could likely find 9mm bolts and end up with about .030". I don't know what
the limit is for the lazer, or the minimum needed to provide a good
surface
for the pinion bearings to ride on.

Ed Carver


I have opened an order with Sunshine metals. Order pending receipt of in
house credit app. and fund transfer. The base price for 28 inches of 4.25"
7075 t73 round bar is $205, of which you want 14". Tax and shipping will
be
added to the end total.
This company will not let me pick it up directly:(

Ed Carver


OK Ed I am in for half.

Paul Lamar



Paul,  As I understand it you are not incorperating provisions for a
hydraulic constant speed prop.  Just for those of us who would like this
feature, how might it be accomplished with a roller bearing supported
propshaft and a planetary gearset.

george grimes

It won't.
Check out Jeans gear box. IMHO CS is not needed for the majority of home
built's as they have such a high power to weight ratio take off is never
a problem. Unless of course you want to improve the MPG by slowing down.
Also those old Hyd CS are heavy at around 50 pounds not including the gov.

Paul Lamar

Ed, I am thinking we will need a 37 mm OD needle pilot bearing
on the inner end of the prop shaft for the sun gear.

I'll do a 3D shortly. That means we should drill the 2 inch holes
only six inches deep and not all the way through the 7 inch long
4 inch bar.

Since the sun gear and the prop shaft turn in the same direction
the pilot bearing will only see the difference in RPM
or about 4000 RPM max.

Something like this will work fine with an inner race.


Paul Lamar


I believe I'm following you, It means we can extend the input shaft further
forward and end up with pilot on each end.

I am thinking of recessing the allen bolts for the planet set into a round
clamping plate in order to provide a surface to thrust against. This may be
necessary with my pusher.

I want to deliver your block tomorrow or wed. I'll bring my rotrex and the
aerocharger, and perhaps a mig welded p port housing if I have the time to
get it done.

Ed Carver

I think the ceramic bearings are more than up to the prop thrust job.

Tomorrow or wed is fine.

I did not know you had a Rotrex. Doug has one too.

Paul Lamar



Tomorrow I am taking the images of the shaft housing to Sheehan foundry and
to Alcastco for a quote. Both companies are within a 3 miles of my house.
This will tell me if I would rather spend the cash on machining from a
solid 6" bar.

I received two quotes on 6061 t6 12x6.25" round, from Industrial metal
supply, and Future alloys.
IMS=$154
Future=$220
IMS also has 6061 t6 half inch wall 6"od tube. This is just a little to
large an id for us.

I am considering using two Sonotube sections to replace the wood block we
intended to use to set the mold. 4' sonotube sections are about $7 at home
depot, and are close to the correct OD. Using this method will eliminate
turning the block down to size.

What finished length do you have in mind for the cast housing?

Ed Carver


Something around 12 inches.
I can't visualize how you would use these tubes to cast aluminum.
How thick are those things?

The pattern must have draft so it will slip out of the sand.

The 4 inch 7075 bar is in the machine shop.


Paul Lamar



The wall thickness of the larger sonotubes is 3/8. Not sure about the 6"
version or the 8" because I have never used these small ones. They are more
than rigid enough to make the mold, and are usually cut with a construction
worm drive skilsaw. The 8" version is a half inch large than the mounting
surface on the 89 bellhousing.

It would be fairly easy to put a taper on the side of the sonotube using
setting type drywall joint compound. The next problem is adding the larger
diameter for the mounting base. That would require cutting a section off of
the length of the 8" tube, then place it around the larger tapered end of
the 6" tube and "mud" it in place, creating a radius at the step in the
process; as shown in your drawing. The setting drywall mud hardens in a
little as 5 minutes, to as long as 2 hours, depending on which setting
speed you select.

If you think the 6" tube is a bit too large, and thus wasteful of casting
material, then Industrial Metal has a nice 6" od tube in the rem pile that
is 16" long, and $13. Just about right for our purposes, perhaps too small
diameter if we consider shrinkage.

How thick should the mounting flange be? It will only extend past the
smaller diameter about and inch. Your drawing appears to show about 1.5"
thickness for that.

Happy to know the 4" shaft is being shaped. Hopefully soon I can think
about the propeller.

Ed Carver

We need a taper on the inside as well.
Perhaps it will work. I am not familiar with those techniques.
Seems cheap enough to give it a try.

I left plenty of material on the pattern so we could adjust the over all
length of the box. Some pushers benefit from a longer gear box.

Don't throw the wood away yet :)

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.