Subject: 3.17:1 gear box super simple PSRU housing casting PCM
From: Rotary Engine
Date: 11/4/2011, 12:17 PM
To: AAA Put this in the To box


Tomorrow I am taking the images of the shaft housing to Sheehan foundry and
to Alcastco for a quote. Both companies are within a 3 miles of my house.
This will tell me if I would rather spend the cash on machining from a
solid 6" bar.

I received two quotes on 6061 t6 12x6.25" round, from Industrial metal
supply, and Future alloys.
IMS=$154
Future=$220
IMS also has 6061 t6 half inch wall 6"od tube. This is just a little to
large an id for us.

I am considering using two Sonotube sections to replace the wood block we
intended to use to set the mold. 4' sonotube sections are about $7 at home
depot, and are close to the correct OD. Using this method will eliminate
turning the block down to size.

What finished length do you have in mind for the cast housing?

Ed Carver


Something around 12 inches.
I can't visualize how you would use these tubes to cast aluminum.
How thick are those things?

The pattern must have draft so it will slip out of the sand.

The 4 inch 7075 bar is in the machine shop.


Paul Lamar



The wall thickness of the larger sonotubes is 3/8. Not sure about the 6"
version or the 8" because I have never used these small ones. They are more
than rigid enough to make the mold, and are usually cut with a construction
worm drive skilsaw. The 8" version is a half inch large than the mounting
surface on the 89 bellhousing.

It would be fairly easy to put a taper on the side of the sonotube using
setting type drywall joint compound. The next problem is adding the larger
diameter for the mounting base. That would require cutting a section off of
the length of the 8" tube, then place it around the larger tapered end of
the 6" tube and "mud" it in place, creating a radius at the step in the
process; as shown in your drawing. The setting drywall mud hardens in a
little as 5 minutes, to as long as 2 hours, depending on which setting
speed you select.

If you think the 6" tube is a bit too large, and thus wasteful of casting
material, then Industrial Metal has a nice 6" od tube in the rem pile that
is 16" long, and $13. Just about right for our purposes, perhaps too small
diameter if we consider shrinkage.

How thick should the mounting flange be? It will only extend past the
smaller diameter about and inch. Your drawing appears to show about 1.5"
thickness for that.

Happy to know the 4" shaft is being shaped. Hopefully soon I can think
about the propeller.

Ed Carver

We need a taper on the inside as well.
Perhaps it will work. I am not familiar with those techniques.
Seems cheap enough to give it a try.

I left plenty of material on the pattern so we could adjust the over all
length of the box. Some pushers benefit from a longer gear box.

Don't throw the wood away yet :)

Paul Lamar


ok, ic, I assumed the center sand column mold would be placed after the OD
mold was set. I can still create that with an extra 4.5" tube inside the 6"
tube.

Ed Carver

It is cheap enough. Make one and let me take a look.

Better yet take it to the foundry and ask them if it will
work.


Paul Lamar



Sheehan foundry needs a pattern that represents one half of the part on
each side of a plate. And they want a core pattern.
Gotta stick with the wood block. No taper necessary on the pattern.
It will be easy to cut the pattern to form two halves after we shape it.

I really don't think it is worth the time to find another foundry to do it
my way.

Are you available today so I can re deliver the block? And how's the
weather, maybe I can give you a push this time.

Ed Carver


Well I took Tracy's computer mounting apart to fix the PCM problem.

Mike mounted the PCM down under the RV4 panel ahead of the stick so I could
not read the thumb wheel number. I am redesigning the whole works so I can
mount it on the right side of the cockpit and make is smaller in the process.
I have no room left on the instrument panel for the stock PCM.

It will be a few days before I am ready to run it again.  If any body wants
a smaller PCM let me know now as I am ordering the parts and the new PC board.
I am using a larger thumb wheel sw as well. You can't tune it if you can't read
the mode number. Some people put the cold start switch and the computer
sw in the instrument panel. Both Mike and Dave did it that way so the PCM
can get smaller. I think I can get it down to 2" by 2".

Give it a few days on the wood block and Michale (the big lathe guy) should
have the prop shafts bored. He will have to machine the pattern block anyway.

BTW what do I owe you for the shaft material?

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.