Subject: 1991 Turbo II exhaust manifold cracking. Att. Michael Hart
From: Rotary Engine
Date: 11/14/2011, 5:42 PM
To: AAA Put this in the To box


Hi Michael,

I think I forgot to perform this operation on your exhaust
manifold. Get a die grinder and 1/8" radius all openings to reduce
the cracking tendency. It only takes a few minutes. Even a Dremel tool
will work but it takes a lot longer.

I have never seen one  catastrophically fail but
small cracks are very common and harmless. However they could grow
into larger cracks. The problem is the sharp edges
as Mazda merely machines the casting without radiusing the holes.

The same thing goes for the turbo itself.

Jap Performance in Moorebank, New South Wales
Has at least a dozen used.
(02) 9601 6715
6 Kelso Crs
MoorebankNSW2170



Here is another list that may have some used manifolds.
Rick's Rotary Performance
     Pleasanton, CA
     925-484-2324
     Rx-7 Performance Work and Service.
     Owner: Rick Soderberg


Rotor Sport
     Campbell, CA
     408-374-1330
     Paul Elenga
     Complete Mazda service and repair


Tri-Point Engineering
     Canoga Park, CA
     818-348-5385
     They stock Racing Beat parts, plus an odd assortment of
     spare used parts.  Work on rotaries.


Shum's Auto Clinic
     San Francisco, CA
     1301 Ocean Ave.
     415-584-6655


Rx-7 Specialties
     Calgary
     403-246-6980

   Maztech
Tampa, FL
813-874-0937


Z-Tech
     529 N. Highway 17-92
     Longwood, FL  32750
     407-695-6000
   specialize in RX-7s.



JT Rotary
Honolulu, HI
808-842-7199
The rotary specialty side of KMA Racing.


Jose's Rotary & Muffler
850 Hwy 80 East
Houghton, IA 71037
318.949.3970



Rotary Connection, Inc.
Lexington, KY  40508
606-254-3858
Specializing in all Wankel-type engine work.

Paul Lamar

If it is not possible to find a good used Turbo II manifold
this is easier to fabricate out of 321 SS 3/16" thick than it looks.
I don't think one may find a new Turbo II manifold but I have not
looked.

It is designed to be interchangeable with the stock cast iron manifold
so no changes would be required in the turbo plumbing.

Paul Lamar

        Hi Paul,

If I get a manifold made out of ss,would that improve the cracking tendency
over the stock manifold or it will not make a difference?.Cause if there is
a considerable improvement then I would rather go with the SS than buying
used stock manifold.Please give me your opinion.


Michael               

The cracks develop very slowly. Dave has 600 hours on his with no radius.

He also raced it at Reno where he was at full power 45" Hg for 15 or 20 minutes at a
time. I would radius the manifold you have and then look at it once a year
when you are required to do your own annual as a home builder.
If it is cracked then there is plenty of time to get a custom made
SS manifold. These cast iron manifolds do not catastrophically fail.

IMHO the radius alone will fix the problem. That was the only real problem
Dave had in 600 hours. He had other problems but those were a result of using
the wrong parts or running the turbo too hard.

I don't expect you will be using as much HP or for as long a period of time
as Dave does when racing. He does not have a turbo tach like yours so if you keep the
turbine RPM below 80,000 RPM you will not get the boost Dave is getting.
Dave is our chief destructive tester on turbo aircraft engines :)

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.