Subject: 1991 Turbo II exhaust manifold cracking. Att. Michael Hart
From: Rotary Engine
Date: 11/14/2011, 11:05 PM
To: AAA Put this in the To box



 Hi Michael,

 I think I forgot to perform this operation on your exhaust
 manifold. Get a die grinder and 1/8" radius all openings to reduce
 the cracking tendency. It only takes a few minutes. Even a Dremel tool
 will work but it takes a lot longer.

 I have never seen one  catastrophically fail but
 small cracks are very common and harmless. However they could grow
 into larger cracks. The problem is the sharp edges
 as Mazda merely machines the casting without radiusing the holes.

 The same thing goes for the turbo itself.

 Jap Performance in Moorebank, New South Wales
 Has at least a dozen used.
 (02) 9601 6715
 6 Kelso Crs
 MoorebankNSW2170



 Here is another list that may have some used manifolds.
 Rick's Rotary Performance
      Pleasanton, CA
      925-484-2324
      Rx-7 Performance Work and Service.
      Owner: Rick Soderberg


 Rotor Sport
      Campbell, CA
      408-374-1330
      Paul Elenga
      Complete Mazda service and repair


 Tri-Point Engineering
      Canoga Park, CA
      818-348-5385
      They stock Racing Beat parts, plus an odd assortment of
      spare used parts.  Work on rotaries.


 Shum's Auto Clinic
      San Francisco, CA
      1301 Ocean Ave.
      415-584-6655


 Rx-7 Specialties
      Calgary
      403-246-6980

    Maztech
 Tampa, FL
 813-874-0937


 Z-Tech
      529 N. Highway 17-92
      Longwood, FL  32750
      407-695-6000
    specialize in RX-7s.



 JT Rotary
 Honolulu, HI
 808-842-7199
 The rotary specialty side of KMA Racing.


 Jose's Rotary & Muffler
 850 Hwy 80 East
 Houghton, IA 71037
 318.949.3970



 Rotary Connection, Inc.
 Lexington, KY  40508
 606-254-3858
 Specializing in all Wankel-type engine work.

 Paul Lamar

 If it is not possible to find a good used Turbo II manifold
 this is easier to fabricate out of 321 SS 3/16" thick than it looks.
 I don't think one may find a new Turbo II manifold but I have not
 looked.

 It is designed to be interchangeable with the stock cast iron manifold
 so no changes would be required in the turbo plumbing.

 Paul Lamar

         Hi Paul,

If I get a manifold made out of ss,would that improve the cracking tendency
over the stock manifold or it will not make a difference?.Cause if there is
a considerable improvement then I would rather go with the SS than buying
used stock manifold.Please give me your opinion.


Michael               

The cracks develop very slowly. Dave has 600 hours on his with no radius.

He also raced it at Reno where he was at full power 45" Hg for 15 or 20 minutes at a
time. I would radius the manifold you have and then look at it once a year
when you are required to do your own annual as a home builder.
If it is cracked then there is plenty of time to get a custom made
SS manifold. These cast iron manifolds do not catastrophically fail.

IMHO the radius alone will fix the problem. That was the only real problem
Dave had in 600 hours. He had other problems but those were a result of using
the wrong parts or running the turbo too hard.

I don't expect you will be using as much HP or for as long a period of time
as Dave does when racing. He does not have a turbo tach like yours so if you keep the
turbine RPM below 80,000 RPM you will not get the boost Dave is getting.
Dave is our chief destructive tester on turbo aircraft engines :)

Paul Lamar

This is Dave Leonard's RX7 Turbo II manifold with 600 hard hours and
the Reno races where he went 229 MPH. This is the longest crack
I have ever seen. I don't know why Dave did not radius the openings
as it was mentioned years ago on here. I guess I need to do an article
for the web site on Turbo do's and don'ts.

Also there is a picture of a 3rd gen dual sequential cracked turbo.
These things are real expensive so you have to be rich
to maintain a 280 HP 3rd gen RX7:) The car was about $35,000
back in 1995 when it first came out. Used 3rd gens are now about
$15,500. One of the lowest depreciation cars ever.

Paul Lamar



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.