One item you mentioned below needs some clarification.
The RX8 coil can not be used in a simple ignition as implied, because of
the
2ms dwell time required. The trigger is at the rising edge of a 2ms
square
wave, and coil firing is at the falling edge. This will give you a
90deg.
retarded ignition at 7500RPM.
I believe we talked about that already a few years back.
It would be nice, if someone came up with a simple electronic setup,
without
a microprocessor, taking care of that.
Richard Sohn
N2071U
www.fairpoint.net/~res12/home.**html<
http://www.fairpoint.net/~res12/home.html
Real easy to do that Richard with a 555. It is called
a non-retriggerable one shot.
Paul Lamar
I missed your point at first. Yes I can see how that
could be a real problem at high RPM.
Paul Lamar
Paul and Richard,
If you use a Hall Effect sensor for your trigger you can use it to advance
the timing too. Kawasaki used this system with some of their old CDI
systems. They would space the sensor as far from the magnet as would
reliably trigger. Then as engine rpm rose the leading edge of the sine
wave
would trigger the thyristor trip voltage sooner naturally. This would
cause
the system to fire sooner and advance the timing. The max advance was
about
12-15 degrees but it was enough to make a difference with not one moving
part. It worked perfectly, and there was no way for it to go wrong if the
sensor was still functional.
Bill Jepson
I was talking to Randy this after noon about the dwell phenomena and I
realized
that I had forgotten that a capacitor discharge ignition does not do that.
If you are using a carb and you need a stand alone ignition just buy
an MSD capacitor discharge system. CD systems use the same old simple
coil differently. They do not use the rapid break down of the magnet
field in the coil to form the spark. They use the coil as a pulse
transformer.
When the capacitor charge is dumped into the primary winding of the coil
it fires the plugs with no delay. Within microseconds. No need for a dwell
time
to build up the current in the coil.
Of course this gives you no advance but it solves the retard problem
mentioned by Richard due to the required dwell time being a significant
amount of time relative to the time it takes the engine to make one
revolution at 7500 RPM.
You may want to add a mechanical advance for high altitude lean burn
as per the jpg.
Paul Lamar
Paul:
Check out the DYNATECH ARC-2 at
http://www.dynaonline.com/skins/products/sportbikes/arc_2/. Looks like it
has 2 triggered inputs to CDI ignition that could easily use the
hall-effect
trigger (or other OEM trigger).
Richard
Looks good. You need two for the trailing plugs on a two rotor
and one for the leading plugs. Very pricey at $400 each.
One can buy an MSD6 on ebay for as little as $50 each.
The cheapest way to implement CDI is use the outboard motor
way and put the magnets on the flywheel. Perfect for a one rotor.
Very reliable. Better than a magneto.
Here are the illustrations. Bill Jepson's advance suggestion
is here as well.
Paul Lamar
To make one thing clear, I do not have any problem with the CDI ignition,
except for the cranking problem. This cranking thing does not show up on the
test stand, because the engine is already worn in(or out) compared to the
new one. My engine runs 6200RPM static WOT. EGT peak is 1700F and engine
sputter starts at about 1500 LOP.
The improvements I am looking for are more of what I like than what I need.
Richard Sohn
N2071U
www.fairpoint.net/~res12/home.html
MSD sells a box that retards the ignition to help starting.
One might even be able to hand prop it.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.