Subject: Mazdatrix one rotor LSA engine. RX8 ignition coils 2 ms dwell
From: Rotary Engine
Date: 11/21/2011, 2:13 PM
To: AAA Put this in the To box


   One item you mentioned below needs some clarification.
   The RX8 coil can not be used in a simple ignition as implied, because
of
   the
   2ms dwell time required. The trigger is at the rising edge of a 2ms
 square
   wave, and coil firing is at the falling edge. This will give you a
 90deg.
   retarded ignition at 7500RPM.
   I believe we talked about that already a few years back.

   It would be nice, if someone came up with a simple electronic setup,
   without
   a microprocessor, taking care of that.

   Richard Sohn
   N2071U


http://www.fairpoint.net/~res12/home.html

   Real easy to do that Richard with a 555. It is called
   a non-retriggerable one shot.

   Paul Lamar

   I missed your point at first. Yes I can see how that
   could be a real problem at high RPM.

   Paul Lamar


 Paul and Richard,
 If you use a Hall Effect sensor for your trigger you can use it to
advance
 the timing too. Kawasaki used this system with some of their old CDI
 systems. They would space the sensor as far from the magnet as would
 reliably trigger. Then as engine rpm rose the leading edge of the sine
 wave
 would trigger the thyristor trip voltage sooner naturally. This would
 cause
 the system to fire sooner and advance the timing. The max advance was
 about
 12-15 degrees but it was enough to make a difference with not one moving
 part. It worked perfectly, and there was no way for it to go wrong if the
 sensor was still functional.
 Bill Jepson

 I was talking to Randy this after noon about the dwell phenomena and I
 realized
 that I had forgotten that a capacitor discharge ignition does not do
that.

 If you are using a carb and you need a stand alone ignition just buy
 an MSD capacitor discharge system. CD systems use the same old simple
 coil differently. They do not use the rapid break down of the magnet
 field in the coil to form the spark. They use the coil as a pulse
 transformer.
 When the capacitor charge is dumped into the primary winding of the coil
 it fires the plugs with no delay. Within microseconds. No need for a
dwell
 time
 to build up the current in the coil.

 Of course this gives you no advance but it solves the retard problem
 mentioned by Richard due to the required dwell time being a significant
 amount of time relative to the time it takes the engine to make one
 revolution at 7500 RPM.

 You may want to add a mechanical advance for high altitude lean burn
 as per the jpg.

 Paul Lamar


 Paul:

 Check out the DYNATECH ARC-2 at
 http://www.dynaonline.com/skins/products/sportbikes/arc_2/. Looks like it
 has 2 triggered inputs to CDI ignition that could easily use the
 hall-effect
 trigger (or other OEM trigger).

 Richard

 Looks good. You need two for the trailing plugs on a two rotor
 and one for the leading plugs. Very pricey at $400 each.

 One can buy an MSD6 on ebay for as little as $50 each.


 The cheapest way to implement CDI is use the outboard motor
 way and put the magnets on the flywheel. Perfect for a one rotor.
 Very reliable. Better than a magneto.

 Here are the illustrations. Bill Jepson's advance suggestion
 is here as well.


 Paul Lamar


To make one thing clear, I do not have any problem with the CDI ignition,
except for the cranking problem. This cranking thing does not show up on
the
test stand, because the engine is already worn in(or out) compared to the
new one. My engine runs 6200RPM static WOT. EGT peak is 1700F and engine
sputter starts at about 1500 LOP.

The improvements I am looking for are more of what I like than what I
need.

Richard Sohn
N2071U
www.fairpoint.net/~res12/home.html


MSD sells a box that retards the ignition to help starting.
One might even be able to hand prop it.


Paul Lamar

From what I understand, the MSD does not fire unless the 2nd trigger
occurs no more then 200ms after the first one. What I found was it is
firing at 350RPM but not at 250RPM. I was told that there is a similar
feature in Tracy's ECU for preventing it to fire if it is triggered just
one time.

If that is correct, a timing retard would not make a difference.

Richard Sohn
N2071U
www.fairpoint.net/~res12/home.html


Have you contacted MSD on this Richard?
http://www.msdignition.com/troubleshooting.aspx

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.