Subject: 20B in a Seawind....on Utube-anyone we know?
From: Rotary Engine
Date: 11/22/2011, 5:34 AM
To: AAA Put this in the To box


Found this, wonder who it is?

http://www.youtube.com/watch?v=V2HUHKqTHTg


seems to have a dry sump and Tracy's psru?



Marc Wiese

My guess is its Bob Darrah's in Austin Texas.

Paul Lamar

--------------------------------------------------------------------------
-------- Original Message --------
Subject: Three rotor Knowledge
Date: Mon, 03 May 1999 08:32:38 -0700
From: Paul <rotaryeng@earthlink.net
To: zz <rotaryeng@earthlink.net

Bob Darrah wrote:

 I have parts of a 20B spread all over my garage, it looks like I may have
some parts left over after I get it put  together.

 More dumb questions:
 Is the rotor considered to be at TDC when a radius through the apex is
horizontal toward the spark plugs?
 Is another apex  at BDC at the same time?
 In ignition timing, is the 30 degrees BTC 30 degrees of shaft rotation  (10
degrees of rotor rotation)?

 Now, more serious questions:  in the rotor housing exhaust ports, there  is
a baffle near the top of the exhaust
 port that leads to a second passage that eventually goes into a passage  in
the intake manifold.  I assume it is to
 heat the intake.  It seems to me this would defeat the purpose of an
 intercooler.


 Do I  (1) block this off?

 What is the preferred method?

 (2)Grind the lip of the baffle out, slightly increasing the effective
  size of the exhaust  port.

 (3)Utilize it somehow?  Or what?

 Any tips on how to put this thing back together utilizing ALL the parts  would be appreciated!

 Thanks
 Bob Darrah

----------------------------------------------------------------------------------------------
-------- Original Message --------
Subject: Sea Wind cooling duct.
Date: Fri, 19 Jul 2002 18:03:54 -0700
From: ACRE NL <rotaryeng@earthlink.net>


> > OK Bob, Here it is. My best guess.
> > The top panel is flat as I assume you will use a spinner.
> >
> > I would check it with a pickup truck for uniform air flow
> > and good dynamic pressure recovery first if I were you.
> >
> > I would not want to have your expensive three rotor overheat on its
> > first flight. Pick a cool morning.
> >
>
> Thanks, Paul, I'll give it a try in cardboard first.  The only thing that
> bothers me is the size of the inlet-less than 40 sq inches.  I thought it
> should be about 1/4 the size of the radiator-125 sq inches or so.
>
> I appreciate your efforts!
>
> Bob Darrah

While driving the 100 miles round trip to the hangar this afternoon
I thought about it some more and it seems to me, given the shallow
angle of the rad, that a simple plain wedge shaped duct will work
as well as anything else. Just keep that last corner sharp.
As in this jpg. This one has a lot more intake area as well
with out getting too high over the spinner. This one may very
well work much better.

Got any pictures of your engine installation. That would help
me visualize what we are dealing with here.

You could get your local air conditioning sheet metal guys
to make a couple of cheap steel prototypes for testing.

Paul Lamar

The AirCraft Rotary Engine NewsLetter.              Powered by Linux.
ACRE NL web site. Copyright 1998-2002 All world wide rights reserved.
http://home.earthlink.net/~rotaryeng/            http://www.linux.org

----------------------------------------------------
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.